Replacement Lock Cylinder Compatibility with Leer Camper Shell

Question

Question:

I have a Leer 100R camper shell on my Toyota Tacoma. Will these lock cylinders work in the handles on my camper?

asked by: Jon R

0

Expert Reply:

The Leer 100R camper shell does not have lock cylinders that are directly compatible with anything we currently offer. The Bolt Lock # BL7023482 you referenced are for tool boxes and the product dimensions are 2 x 1.5 x 1.5 inches.

expert reply by: Jason S

0

Answer 1

Thanks for reaching out, Hal! That's a really good question. Based off what I could find, if the old cylinder worked with your ignition key you would want to get part #BL692918. I included the ignition key compatibility diagram below for you. You…

view full answer...

Answer 2

Yes, the BOLT Replacement Lock Cylinder #BL7023482 will code to the ignition key for your 2015 Toyota Tacoma. I have attached an image below of the compatibility chart for this particular cylinder and it lists all models of the 2015 Tacoma as a…

view full answer...

Answer 3

I can help you find the right replacement lock cylinder for your 2007 Chevy Avalanche LT Toolbox. If your current lock cylinder can be removed from your Avalanche's toolbox then you will need the Late Model GM Key Cylinder from BOLT #BL692915.…

view full answer...

Answer 4

Hello David, thanks for reaching out. I will need more information on your camper shell in order to know what locks will work. Can you provide the model number from your shell? That will help a lot to narrow things down. For example, if your ARE…

view full answer...

Answer 5

I do have an option for you to get the locks working again but we don't carry Load Lock so I don't have any advice or replacement parts for this. That said, you should be able to pretty easily replace this with the Pop & Lock Power Lock…

view full answer...

Answer 6

Yes, the Pop & Lock Power Lock Conversion Kit for Truck Caps and Hard Tonneau Covers part #PAL9772 or part #PAL9555 will work on the Leer 100XQ Truck Caps because it uses a cable latching mechanism and the handle is not riveted on.

view full answer...

Answer 7

Hey Erik, so we checked with Pop & Lock, and while they did not say whether the Power Locking Handle #PAL9555 could fit a Leer 100R cap, they did provide information about the requirements you need on your cap. Firstly, your truck must be already…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hi Steve; the factory hitch on the 2013 Tacoma has the bumper brackets integrated into the hitch. You can replace it with the etrailer Trailer Hitch #e98850 but you will have to remove the old hitch and find new bumper brackets to complete the…

view full answer...

Answer 11

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 12

Hey David, this is a great question but essentially there is no difference between the two Redarc Tow Pro Liberty brake controller part numbers #RED72CR and #RED68CR that both fit your 2017 Toyota Tacoma. Basically it's two part numbers that have…

view full answer...

Replacement Lock Cylinder Compatibility with Leer Camper Shell

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching