Compatibility of BOLT Lock Cylinder on 2007 Chevy Avalanche LT Toolbox

Question

Question:

IVE RECENTLY purchased an 07 Chevy avalanche LT and the tool box or side storage boxes on each side of the bed dont lock...is this the proper lock cylinder to replace them? Thanks

asked by: Mark

0

Expert Reply:

I can help you find the right replacement lock cylinder for your 2007 Chevy Avalanche LT Toolbox.

If your current lock cylinder can be removed from your Avalanche's toolbox then you will need the Late Model GM Key Cylinder from BOLT # BL692915. Usually, if the lock is going to be able to be replaced it will have a thin nut on the back of the cylinder on the interior of the toolbox that can be loosened and removed. I've included an image to show you what I'm talking about.

If you happen to have a latch that doesn't have a removable cylinder we offer the BOLT Latch Retro Fit Kit replacement # BL7022697. This retrofit latch kit for your toolbox has a lock that codes to your vehicle's ignition key. Corrosion-resistant lock is made of automotive-grade materials and is nearly impossible to pick or bump.

expert reply by: Jackie C

0

click to enlarge

Answer 1

Thanks for the picture of the key you have! The Bolt Lock Cylinder part #BL692918 is a fit based on seeing that and knowing you have a 2002 Avalanche.

view full answer...

Answer 2

Thanks for reaching out, Hal! That's a really good question. Based off what I could find, if the old cylinder worked with your ignition key you would want to get part #BL692918. I included the ignition key compatibility diagram below for you. You…

view full answer...

Answer 3

Hello Tyler, thanks for reaching out. We may have what you need, but I will need more information in order to know what locks will work. Does your ARE cap use the Bolt brand locks that key to your ignition key? If so, the Replacement Lock Cylinder…

view full answer...

Answer 4

Yes, the BOLT Replacement Lock Cylinder #BL7023482 will code to the ignition key for your 2015 Toyota Tacoma. I have attached an image below of the compatibility chart for this particular cylinder and it lists all models of the 2015 Tacoma as a…

view full answer...

Answer 5

The Leer 100R camper shell does not have lock cylinders that are directly compatible with anything we currently offer. The Bolt Lock #BL7023482 you referenced are for tool boxes and the product dimensions are 2 x 1.5 x 1.5 inches.

view full answer...

Answer 6

Since your trailer uses a combined wiring system where the stop and turn signals run on the same circuit, in order to add a third brake light to your trailer you would need to use a 2-Wire to 3-Wire Converter, like part #118158. This will convert the…

view full answer...

Answer 7

A 2016 Chevy Colorado should have a center cut transponder key so you would need the Replacement Lock Cylinder for BOLT Toolbox Latch - Codes to Center Cut GM Key #BL7023480. This is just the replacement lock cylinder so if you're needing parts…

view full answer...

Answer 8

For a simple cam lock, you can get an old standard blade screwdriver that you don't care about messing up. Use a hammer and drive the screwdriver into the key slot, the further the better. Use a pipe wrench on the screwdriver handle, and turn. In…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Compatibility of BOLT Lock Cylinder on 2007 Chevy Avalanche LT Toolbox

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching