Grease Seal Replacement Recomendation for Lippert Seal 122088

Question

Question:

I need Lippert part # 122088 grease seals, double lip. 2.25ID x 3.376inch OD. Do you carry that size? Thanks inner and outer seal kits

asked by: Jim M

1

Helpful Expert Reply:

We have just what you need. The grease seal you are looking for is our part # RG06-070 which matches the dimensions you listed and is a double lip seal. Hubs only have inner seals though as a grease cap sits on the outside. Are you looking for a cap as well?

expert reply by: Jameson C

1

Answer 1

Hi Fred; the Norcold N8XFL fits a cutout measuring 59.875"H x 23.5"W x 24"D. The equivalent size Dometic would be the Dometic Americana II RV Fridge #DMC22RR. This fits a cutout measuring 59.94" H x 23.69" W x 24" D.…

view full answer...

Answer 2

The Dexter Grease Seal 010-036-00 is interchangeable with the Dexter Grease Seal 010-054-00 although they have a slightly different outer diameter, 3.371" (010-036-00) vs 3.376" (010-054-00) but they do both have the same inner diameter of…

view full answer...

Answer 3

Lippert's roller tubes are not a universal fit so they have not been confirmed to fit on a Dometic awning. I recommend upgrading to a Lippert awning like the Solera Smart Arm 12V Power RV Awning - 18' Wide - Programmable - White Fade…

view full answer...

Answer 4

You were on the right track. To raise the tires off the ground for long term trailer storage, the best way is to use your front jack to raise the trailer then place the jack stands under the frame by each axle on all four sides. I have attached a…

view full answer...

Answer 5

Welcome back Steve! We definitely have brakes that will fit your 4,400 pound Lippert axle, but I will admit to being a little confused by the measurements you got. Brand new brake shoes will measure 3/16" (or 4.7mm) and you want to replace them…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Grease Seal Replacement Recomendation for Lippert Seal 122088

Product Page this Question was Asked From

Continue Researching