Dimensions of Holes on Titan 2-Tang Clevis with Channel Mount # T1812200

Question

Question:

What is the diameter of the mounting hole and the spacing of the mounting holes? Thank you!

asked by: Eric K

1

Helpful Expert Reply:

The mounting holes are 2 inches on center for the clevis and 3 inches on center for the mount. The clevis and side of the bracket has holes that are 0.64 inch. The top and bottom holes of the mounting bracket are 0.48 inches and the center hole is 0.33 inches.

I've attached some photos to assist.

expert reply by: Jason S

1

click to enlarge

Answer 1

I would be happy to help. It sounds like you are looking for the Demco 2-Tang Clevis #DM12676-95 which will fit perfectly in the Curt Channel Style Adjustable Ball Mount #C45900 you have. The clevis bolt is not included but a 1" diameter bolt…

view full answer...

Answer 2

That is a pretty good guess! The two position mounting channel in the #T1812200 is 3-1/2" wide x 7-1/2" tall as shown in the included diagram. I included a video review of the #T1812200 for you to take a look at.

view full answer...

Answer 3

I have a solution for you, however, unfortunately, the Titan 3-Position Adjustable Channel Bracket, #T0897800, is a bolt on application. If you are needing a weld-on bracket, the Demco 4-Hole Adjustable Channel Bracket, #DM66736, is what I…

view full answer...

Answer 4

Hi Daide, That's an interesting set up your client has there, and while we don't have anything specifically in that realm, there's an option for you by using channel-mounted couplers. So either of the following could work: - Demco 4-Hole…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Dimensions of Holes on Titan 2-Tang Clevis with Channel Mount # T1812200

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching