Size of Wrench/Socket for Nut on Hitch Ball of Curt Ball Mount # C45331

Question

Question:

Hi! What size socket is the nut? Thx

asked by: Tyler

1

Helpful Expert Reply:

The size of wrench or socket needed tighten or loosen the nut of the ball mount # C45331 is 1-7/8 inch. It's on there with quite a bit of torque as the rating for the nut is 450 ft lbs of torque.

expert reply by: Jameson C

1

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 7

Hey Gregory, that's really good information. You’ve got a few options, but I wouldn’t jump straight to replacing the leaf springs on a half-ton for that size trailer. Since you’re using a Curt weight distribution hitch, that should be doing most…

view full answer...

Answer 8

Hey Don, thanks for the information! That's a significant amount of sag and a pretty heavy trailer, I recommend the Hellwig Pro Series Helper Springs item #HE79FR for the higher 2,500 lbs capacity. I doubt you're driving around with your bed…

view full answer...

Answer 9

There sure is K.C.. For a shorter weight distribution shank that fits a 2-1/2" hitch, I recommend the Equal-i-zer item #EQ90-02-4700. This shank measures 12" long x 9-1/2" tall. It provides up to a 3" drop and has a 16,000 lbs…

view full answer...

Answer 10

Hey Douglas, whenever available I recommend going with the HD version of the Roadactive kits like the part #RAS3611-YHD that fits your 2022 Ford F-150 4WD. The extra capacity of this kit over the non-HD basically doesn't have any downside aside…

view full answer...

Answer 11

Hey Dennis! I can't say if it will clear for sure but I can give you dimensions to help determine if it will. Using the furthest hitch pin hole, the Malone 2" Dual Purpose Hitch Receiver #MPG544 will push the bike rack out 12-1/4". When…

view full answer...

Answer 12

Hey Jason! I'm guessing you have the 12" long shank right now which is the standard. For a longer shank that fits a 2-1/2" receiver you can use the Equal-i-zer Weight Dist Shank - 2-1/2" Hitch - 16" Long - 7" Rise,…

view full answer...

Size of Wrench/Socket for Nut on Hitch Ball of Curt Ball Mount # C45331

Product Page this Question was Asked From

Continue Researching