Curt Brake Controller Install Harness Recommendation for 1999 Ford F-250

Question

Question:

i need a plug in harness for a 1999 f 350 super duty

asked by: Nick

0

Expert Reply:

For installing a Curt brake controller like the Triflex part # C24VV in your 1999 Ford F-250 the correct install harness is the part # C51322 which is a confirmed custom fit and would work well.

expert reply by: Jameson C

0

Answer 1

Welcome to the brake controller game James! We're glad you're here. With the factory equipment you already have on your vehicle, adding a brake controller will be really straightforward. I'd definitely recommend the Redarc Tow-Pro Liberty…

view full answer...

Answer 2

Yes, you can use a fuse tap like the part #F2526 to tap into the stoplight circuit of the vehicle for a dedicated brake signal for installing a brake controller. Any time the brake lights are turned on this circuit would have voltage on it.

view full answer...

Answer 3

If the hub that was on your trailer axle previously had 8-91A stamped on the back of it your spindle should require inner and outer bearings of #L44649 like you used. The part #8-91-05UC1 SHOULD be an exact replacement. However we need to double…

view full answer...

Answer 4

Hey Jacqueline! The Dexter Self-Contained Hydraulic Jack #DX72CR manual didn't have anything in it about a manual override, but in looking at the photos, the rubber plug on top of the cover should be where the manual override is located. Try…

view full answer...

Answer 5

Hey James, bypassing your integrated controller does require some wire but not a trip to the dealer... Installing the P3 brake controller #90195 on your 2022 Chevy Silverado 2500 with factory integrated controller will actually be very simple. What…

view full answer...

Answer 6

Hello Steve, thanks for reaching out. The #C51525 is the correct harness for the 2024 Silverado 2500. The factory plug under the dash should look like the plug in the picture below. Is it possible you are not looking at the correct plug? It should be…

view full answer...

Answer 7

Hey Ray, while there certainly is a lot of appeal to the Andersen WD systems like the part #AN88VR what we have found is that if the tongue weight is more than a few hundred lbs they just don't work as well as the traditional systems that use…

view full answer...

Answer 8

It appears the wiring to connect a Trailer Brake Controller #90195 on your 2024 GMC Yukon are going to be high up on your dash close to the left side of the drivers compartment. You can start by removing the left side panel of the dash which sits up…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Curt Brake Controller Install Harness Recommendation for 1999 Ford F-250

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching