Brake Controller for 2014 Mitsubishi Outlander

Question

Question:

Hello Kyle, I bought and installed the 4 pin which you recommend. I'm planning to use Curt Echo What else Do I need?

asked by: Rod

0

Expert Reply:

I can get you set up with everything you need to add a brake controller to your 2014 Mitsubishi Outlander. You were correct in starting with the 4-way like # 118482.

You will also need the Universal Installation Kit for Trailer Brake Controller # ETBC7, which will give you a 7- and 4-way trailer connector (which you will plug your trailer's 7-way into), circuit breakers and the rest of the hardware needed to install a brake controller.

As for the brake controller itself, I strongly recommend the Prodigy P3 # 90195; it is the most popular model we carry due to its effectiveness and ease of use. It will activate your trailer's brakes immediately in proportion to your Outlander's brakes and offers three different boost levels so you can adjust your braking power.

All of this together will give you what you need to install the controller in your Outlander. I have also added a couple articles for you on brake controller installation that I recommend you take a look at.

expert reply by: Kyle S

0

Rod

7/18/2018

Hello Kyle, I bought and installed the 4 pin which you recommend. I'm planning to use Curt Echo What else Do I need?

Kyle S.

7/18/2018

Hello! Since you do not have the factory tow package the only other thing you need to install the Curt Echo Mobile Trailer Brake Controller # C51180 is the Installation Kit # ETBC7L which will give you the rest of what you need to install a wireless brake controller in your Outlander.

Answer 1

The wiring harness I highly recommend for your 2014 Mitsubishi Outlander, because of its reliability and ease of install, is the Tekonsha T-One Vehicle Wiring Harness #118482. We have found the Tekonsha brand to be by far the most reliable trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 9

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Brake Controller for 2014 Mitsubishi Outlander

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching