Curt TruTrack Weight Distribution System Setup

Question

Question:

I have the Curt 17500. Single axle TT. 4000# fully loaded. 2010 Ram 1500. 1250# payload, 9950# max towing. In watching several videos on the correct setup procedure, I have seen a wide variance in the advice as to how high to initially set the ball over the level-height of the trailer ball coupler. One said 1/8inch for every 100# of estimated tongue weightinch between 1/2inch and 3/4 and one said 3 inches! Please tell me the correct way to set the ball height relative to my trailers coupler. I want to do it right and DIY... Thanks!

asked by: John C

0

Expert Reply:

When using the Curt TruTrack Weight Distribution System w/ Sway Control # C17499, which is a great system for your trailer weight and vehicle, you will initially setup your system just like you would a ball mount. So you will measure from level ground to the bottom of your trailer coupler when the trailer is sitting level to the ground. Then you will adjust the hitch ball height on your trailer to correspond to that measurement at the base of the platform the hitch ball rests on. I've attached an article to assist as well as installation instructions for the TruTrack.

When you add the trailer weight to the ball it will drop the back end of your truck, but when you apply the spring bars to the brackets it should bring it back to level. You may need to make some adjustments with the initial fit to ensure you have level transport of both your truck and trailer with the system engaged. Once you have found the correct fit, it makes each time you connect the system extremely easy.

expert reply by: Jason S

0

Answer 1

I check the owner's manual of your 2020 Ram 1500 and the fuse for the 12v power pin on your 2020 Ram 1500 is located in the fuse box underneath the instrument panel on the driver side, and the fuse is F01 which is a 30amp pink fuse. Check to make…

view full answer...

Answer 2

Since you are installing your Curt TruTrack Weight Distribution System #C17500 on your 2021 Ford F-150 truck you will not use step 3. This step is only required for cars, vans and small SUV's as their suspension is not intended for towing with a…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 7

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Hey Michelle! There are definitely a lot of different weight distribution hitch (WDH) options out there. The most important thing is to make sure it is properly rated for the tongue weight of your setup. Looking at the specs for the 2022 Keystone…

view full answer...

Answer 10

Hey Michael, welcome back! The Alpha Systems 1021 Self-Leveling Sealant #AL98KV is going to do the same thing as Dicor as long as we're talking about a self-leveling sealant. The main difference is going to be the branding. They both use a butyl…

view full answer...

Answer 11

Hi Rick, LaSalle Bristol's roof membrane is made of PVC which is known to be durable and offer better protection against punctures and overall weathering. Alpha Systems offers TPO roof membranes that are more environmentally friendly/recyclable…

view full answer...

Answer 12

Hello Mike, thanks for reaching out. We have roof replacement kits from LaSalle Bristol that are great quality and come with everything you need. I'd just need to know the size of your RV or how many feet of roof membrane you need. For example,…

view full answer...

Curt TruTrack Weight Distribution System Setup

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching