Mounting Hardware for Karrite Voyager Cargo Box

Question

Question:

HI! I just came across info here where I can get a replacement end latch and lock and key for this older model hard sided KarRite Voyager car top carrier I have. I got it for free just hoping to be able to find parts and VOILA!!! Found em! Here no less... SO, I got the part numbers for the lock with key and the end latches, But what parts would I use to get new straps and clips for it to secure to the car??? Thanks!!!

asked by: Lori

0

Expert Reply:

Glad we could help you find the locks for your Karrite Voyager rooftop cago carrier. And while we do not carry direct replacement mounting hardware for this box there is still a solution for you. What you can do is use hardware kit # CTC-18PARTS; this will require you to modify the box and drill holes so use Sealant # LT37467 to cover those holes up.

expert reply by: Kyle S

0

Answer 1

To mount your Karrite Voyager Roof Box to the crossbars on your vehicle your best bet is going to be with the Replacement Hardware Kit #TH05603. The exact/original hardware for the Voyager is no longer available but the plates and U-bolts included…

view full answer...

Answer 2

I went and measured the hinge and mounting plate for the SportRack Replacement Hardware Kit #SR05587 and made a diagram for you to check out. As there were a few measurements listed on it, it seemed the better way to get them to you than typing them…

view full answer...

Answer 3

For starters, the vast majority of cargo boxes and replacement mounting hardware for cargo boxes will not work on factory crossbars for a Nissan Xterra as they are very large in comparison to the standard crossbar sizes that these cargo boxes and…

view full answer...

Answer 4

The Karrite Voyager was a distant relative to the current Thule Sidekick Cargo Box #TH78GC. The box uses standard U-bolt hardware to attach to roof rack crossbars and tightens down with the included plates and threaded knobs. I have attached the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi LaMar, To add a 7-way plug to your 2024 Toyota Highlander SLE you'll need to use the etrailer Universal Installation Kit for Trailer Brake Controllers part #ETBC7. This kit will give you a functioning 4-way flat and 7-way for towing and…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 11

Hello Steve, Thanks for reaching out! We do have a plug-and-play option for your vehicle, though it looks like it didn’t come up in the fit guide, and I’m glad you checked. For your 2024 Toyota RAV4, I recommend the Curt T-Connector Vehicle Wiring…

view full answer...

Answer 12

Hi David! We do have a plug in wiring harness for your 2024 Toyota Highlander XLE with the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #C56RV. This is fully plug and play and will use that square port/plug you already…

view full answer...

Mounting Hardware for Karrite Voyager Cargo Box

Products Featured in This Question

Continue Researching