Replacement AC Shroud for Coleman 7333C8876

Question

Question:

hello i need a replacement shroud that would fit my coleman 7333c8876

asked by: Andre

1

Helpful Expert Reply:

The Coleman 7333C8876 will need the MaxxAir TuffMaxx Replacement Shroud - White # MA00-325001 based on my research because that unit can be interchanged with a Coleman Mach 3. I've attached a diagram of the shroud measurements and a video to assist.

expert reply by: Jason S

1

click to enlarge

Answer 1

As far as refrigerator vents, we carry 2 options. Those are the Camco RV Refrigerator Vent Cover - Base Only #CAM42161 (white) or #CAM42164 (black). These models both have external dimensions of 26-1/4" long x 7-3/8" wide x 1-3/4" tall…

view full answer...

Answer 2

The replacement shroud you need for your Coleman-Mach air conditioner on your 2000 Tioga motor home is the MaxxAir Replacement RV Air Conditioner Cover - Coleman-Mach / RVP Brand RV Air Conditioners Item #MA8335A5261.

view full answer...

Answer 3

Based on the research I've done, it sounds like you 1986 Winnebago LaSharo has an older Coleman Mach 3 series AC unit. So the correct replacement shroud is the MaxxAir TuffMaxx Replacement Shroud for Coleman-Mach RV Air Conditioners #MA00-325001.…

view full answer...

Answer 4

Given the issue you described and the fact that you have done a good job of troubleshooting and checking other potential sources for the issue, it sounds like the motor is going bad. Since you mentioned the landing gear working fine for a little bit…

view full answer...

Answer 5

I was able to determine from some research that your Coleman 7333C8876 can be interchanged with a Coleman Mach 3, so you'll want the MaxxAir TuffMaxx Replacement Shroud - White #MA00-325001 to replace the shroud on your unit. I've linked a…

view full answer...

Answer 6

The MaxxAir Replacement RV Air Conditioner Cover - Coleman-Mach / RVP Brand RV Air Conditioners - White #MA8335A5261 is the correct fit for your 7300 series RVP. The shroud is 37 inches by 25 by 13-1/2 inches. If you don't want the two piece unit…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement AC Shroud for Coleman 7333C8876

Featured Help Information

Miscellaneous Media

Continue Researching