16 inch by 6 inch Trailer Wheel with 6 Bolt Pattern and 3.6 Pilot Diameter

Question

Question:

Im looking for 16x6 inch rim bolt pattern is 6 x 5.5 but center bore is 3.60 inches cant find any did not know if you might know of any thank you

asked by: Scott

0

Expert Reply:

We have the Conventional Trailer Wheel part # AM20758 which is a 16 inch diameter by 6 inch width wheel with a 6 on 5-1/2 inch bolt pattern and a pilot diameter of 3.65 inch. This should work well for you based on what you listed needing.

expert reply by: Jameson C

0

Answer 1

What I found online points to the 17-118 number being the manufacturer's part number, which is identical to the #AM20514 wheel we offer that you'd looked at. I wasn't able to find anything on the 01711800 number you provided, which seems…

view full answer...

Answer 2

The pilot diameter on a wheel, like the one with part #AM30620, is the diameter of the bigger hole that is directly in the middle of the wheel. The pilot hole diameter of the wheel for the part I just measured is 2.84". I have attached a picture…

view full answer...

Answer 3

The 7.00-15LT tires you have on your 1978 Avion trailer have a 29.4" diameter, have a load range that should be in the 2,400 lb vicinity and fit wheels that are 5", 5-1/2" and 6". For comparable tires I recommend going with a…

view full answer...

Answer 4

Yes, we do have baby moon hubcaps that will fit the Dexstar Steel Mini Mod Trailer Wheel - 15" x 6" Rim - 5 on 4-1/2 item #AM20545. They are the Americana Baby Moon Trailer Wheel Center Cap - Chrome-Plated Steel - Qty 1 item #AM90086.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

16 inch by 6 inch Trailer Wheel with 6 Bolt Pattern and 3.6 Pilot Diameter

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching