Small Gap Between Socket on B&W Turnoverball Gooseneck Hitch and Truck Bed
Updated 06/11/2018 | Published 06/08/2018
Question:
Just installed a BandW gooseneck hitch model 1117in my 2017 f350. I drilled a 4”hole in the bed per manufacturers instructions. After installation the socket that extends up through the bed floor is smaller then the 4” hole which leaves a gap of about 3/16” just want to make sure that this is correct. My old truck had the same kind of hitch but no gap between bed and hitch socket. Any help would be greatly appreciated, thanks
asked by: Keith S
Expert Reply:
The 4 inch hole that you cut in your truck bed in order to install the B&W Turnoverball Underbed Gooseneck Trailer Hitch # BWGNRK1116 is correct. The slight gap that you have between the socket for the hitch ball and your bed is not an issue. As long as you have the bolts for the center plate tightened according to the torque specs listed in the instructions, the hitch isn't going to move at all after installation.
I have attached an installation video on your 2017 F-350 that you can also use for reference.
Product Page this Question was Asked From
B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs
- Gooseneck Hitch
- Below the Bed
- Flip-Over Ball
- 7500 lbs TW
- 30000 lbs GTW
- Wheel Well Release
- Spring-Loaded Loop
- B and W
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Video: Checking Out the B and W Rubber Cover for Stowed Turnoverball
- Shop: Gooseneck Hitch
- Shop: B&W Rubber Cover for Stowed Turnoverball
- Q&A: Gap Between Frame and Bracket on Curt Gooseneck Hitch for 2007 Chevy Silverado 2500 Short Bed
- Video: B and W Turnoverball Gooseneck Trailer Hitch Installation - 2017 Ford F-350 Super Duty
- Shop: B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs
- Shop: B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs
- Shop: B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs
- Shop: Trailer Hitch
- Q&A: What Is An OEM Prep Package And How Do I Know If I Have It
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Trailer Wiring
- Q&A: Does etrailer Carry Furrion Chill Cube w/ Heat Pump to Replace Dometic Duo-Therm
- Search Results: trailer wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs
- Q&A: Does Truck with 6-1/2 ft bed Have to Use Slider Hitch for Turning Clearance with Fifth Wheel Hitch
- Search Results: trailer tires and wheels
- Article: How to Measure for Trailer Hitch Drop
- Shop: Suspension Enhancement
- Video: B&W Companion OEM 5th Wheel Hitch Manufacturer Breakdown
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Fifth Wheel Hitch
- Search Results: gooseneck hitch
- Q&A: Installation Time for Blue Ox BX1128 Flat Tow Base Plate Kit for 2016 Jeep Grand Cherokee
- Video: A Look at the Power Mountain Tallboy 6 Ton Off-Road Bottle Jack with a Military Cargo Trailer
- Search Results: trailer jack
- Shop: Brake Controller
on Gooseneck Hitch
