How Many Screws Come with Torx Trailer Floor and Wall Liner Screw for ACQ Treated Wood # TFX225ACQ

Question

Question:

Is the price stated for just one screw on product #TFX255ACQ? On a big deck this would cost a lot of money. Thanks

asked by: Phil

0

Expert Reply:

Torx Trailer Floor and Wall Liner Screw for ACQ Treated Wood # TFX225ACQ is sold in quantities of 1.

expert reply by: Michael H

0

Answer 1

I would recommend to use the treated torx screws for ACQ (Alkaline Copper Quaternary) treated wood for better corrosion and rust resistance. The treated torx screws like the Redline 2-1/2 Inch Long Torx Trailer Screw for ACQ Treated Wood, part…

view full answer...

Answer 2

Yes, the 2-1/4" Long Torx Trailer Floor and Wall Liner Screw #TFX225ACQ that you referenced does have a 1/4 inch diameter. This screw is specially designed for use on Alkaline Copper Quaternary wood.

view full answer...

Answer 3

The longer 2-1/2" torx screw Item #TFX250ACQ will work the best to attach the boards to the metal frame of your Big Tex trailer when replacing the trailer deck. If you need a torx head screwdriver bit, you can use part #TX430-1.

view full answer...

Answer 4

The PS-8 screws should work very well going into either material you mentioned. The threads are coarse enough that they'll get good hold on the aluminum or the rubber. For best results, you'll want to ensure that as many screws as possible go…

view full answer...

Answer 5

If you did three fasteners across the width of the 12 inch wide board you are using with the part #TFX225ACQ you'd be in good shape.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

The only difference between 7-Way Utility and 7-Way RV is the color of the wires. The pin outs are the exact same so either would work just fine with the other. If you check out the picture I attached you'll see that the functions are all the…

view full answer...

How Many Screws Come with Torx Trailer Floor and Wall Liner Screw for ACQ Treated Wood # TFX225ACQ

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching