How Many Chain Links Are Necessary With Reese Dual Cam Weight Distribution?
Updated 05/22/2018 | Published 05/20/2018
Products Featured in This Question
Question:
I was always told to leave 5 chain links below the snap up on my WD hitch. This was never an issue until I installed the dual cam sway control. The way it is designed the hanger bracket extends the length from the snap up bracket to the trunnion bar by approximately 3”. No matter how I raise, tilt the hitch itself, there is no way to get the proper tension without leaving either 2 or 3 lengths below the snap up bracket. This brings the bar back up nearly parallel with the trailer frame and levels my tow vehicle perfectly. Are there any other tricks I can try or am I ok?
asked by: Rod V
Expert Reply:
According to the directions, you will not want any less than 4 chain links. With regards to your issue, the first thing that comes to mind is you may not have the properly rated weight distribution system; the correct system is going to be one in which your total tongue weight (the tongue weight of your fully loaded and ready to go trailer plus the weight of any cargo behind the rear axle of your tow vehicle) falls in the middle of the system's tongue weight capacity. To make sure you have the properly rated system, you will first need to find your trailer's tongue weight with a scale such as # e99044 or by one of the methods in the help article on determining tongue weight I've added for you.
The other thing that may work for you is a shank with more drop; the Curt # C17123 has a maximum drop of 8-1/4" with trunnion bar systems and maximum tongue weight capacity of 1,500 lbs. I've added a link below to our selection of shanks for you to take a look at.
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: 1 7/8 wrench
- Shop: Towing Mirrors
- Q&A: Recommended Weight Distribution System and a 2" Shank w/a 7" Drop
- Shop: Fastway e2 Weight Distribution Shank - 12" Long - 10-1/4" Rise, 5-1/2" Drop - 1.2K TW
- Shop: Curt Weight Distribution Shank - 14" Long - 7" or 7-1/2" Drop - 1,500 lbs TW
- Shop: Equal-i-zer Wt Distribution Shank - 12" - 13" Rise, 9" Drop - 600 to 1,400 lbs TW
- Shop: Curt Weight Distribution Shank - 12" Long - 7-1/2" or 7" Drop - 1,500 lbs TW
- Shop: Curt Weight Distribution Shank - 10" Long - 5-3/4" or 6-1/8" Drop - 1,500 lbs TW
- Shop: Curt Weight Distribution Shank for 2" Hitches - 7-3/8" Drop - 11-1/2" Rise
- Shop: K-Source Universal Towing Mirrors - Clip On - Convex Mirror - Qty 2
- Q&A: How to Determine Correct Drop for Weight Distribution Shank
- Q&A: Trailer Hitch Ball Wrench Size and Torque Rating for 1-1/4 Inch Hitch Ball Shank Size
- Q&A: Troubleshooting Intermittent Trailer Connection that Loses Connection Over Bumps
- Q&A: Suggestions For Leveling Trailer With Weight Distribution System On New Truck
- Video: 4-Leaf Double-Eye Spring for 3,500-lb Trailer Axles: The Breakdown
- Q&A: How to Select the Proper Length Safety Chains for a Trailer
- Q&A: Installation Instructions for Reese Strait-Line Weight Distribution Systems
- Article: 5 Things to Know About Weight Distribution Hitches
- Search Results: reese trunnion bar
- Search Results: gfi outlet
- Search Results: replacement trunnion bars
- Search Results: glass stove cover
- Search Results: reese dual cam
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: How to Choose a Trailer Brake Controller
- Shop: Trailer Wiring
- Article: How to Measure for Trailer Hitch Drop
on Weight Distribution Hitch
