Replacement Wheel Bolt or Replacement Hub for Haul Master 90145 Utility Trailer

Question

Question:

I’m looking for replacement hub studs for a Haul Master 90154 utility trailer. I do not see a match listed. It appears that the 2 in x 1/2 in are the closest match. What do you recommend?

asked by: John G

0

Expert Reply:

For your utility trailer, I recommend pulling one of the studs and measuring for fit. I've linked the picture measuring the Kodiak Wheel Bolt - 1/2" Diameter x 2" Long # K12WB2 for reference. You will need to use a digital caliper like # PTW80157 to get the precise measurements.

Your other option is to pull your hub and get the bearing numbers and seal number from your hub for a replacement hub. If you can't find the numbers printed on the face of your bearing you can use that digital caliper to measure your spindle. I've attached a photo to help with the measurement locations for that fit. I can get you the correct hub match you based on the measurements shown.

expert reply by: Jason S

0

click to enlarge

Answer 1

Hey Kevin! Your 30205 bearing number isn't a common bearing type, but that's pretty normal for a Harbor Freight trailer. If you can measure the spindle on your axle at the specified locations in the attached photo I can see if we can get you…

view full answer...

Answer 2

To determine if we have a replacement hub that will be compatible, you will need to use a digital caliper and take some measurements of your existing spindles. If you reply with the B, C and D dimensions you find (as shown in the diagram I provided),…

view full answer...

Answer 3

To determine if we have a wheel bearing that will be compatible, you will need to use a digital caliper and take some measurements of your existing spindles. If you reply with the B, C and D dimensions you find (as shown in the diagram I provided), I…

view full answer...

Answer 4

We often hear of weak customer support and limited spare parts availability with "bargain" trailer manufacturers. I found an online copy of the owner's manual for the Harbor Freight Haulmaster utility trailer model 90154 but it includes…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Replacement Wheel Bolt or Replacement Hub for Haul Master 90145 Utility Trailer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching