Strength of Steel Fender to Withstand 200 lb Utilizing as a Step
Updated 07/11/2020 | Published 05/08/2018 >
Products Featured in This Question
Question:
Thanks...note this is a boat trailer so there's really not much room to weld. Do you sell a fender that you would recommend for standing on? I understand the bit about brackets, but they will be only on the bottom edge.
asked by: Ted
Expert Reply:
The Single Axle Trailer Fender # HP56VR is made of 14 gauge steel and has one edge that is a 90 degree angle to weld it to your trailer and the other has a more rolled edge. The strength of the fender and ability to hold 200 lbs is based on your mounting. To stand on this fender, you will need to not only weld the edge but also as you stated add brackets which will support the weight. The steel is strong, but I recommend using brackets that can hold the weight on their own to ensure you won't have any deformation on your trailer fender when you step on it. You wouldn't have any issue on the welded side, but the further you move to the outside edge the more risk of deforming without proper bracing for that purpose.

Bill G.
7/7/2020
Can I bolt this fender to the side of an enclosed trailer?

Product Page this Question was Asked From
Single Axle Trailer Fender for Enclosed Trailers - Cold Rolled Steel - 15" Wheels - Qty 1
- Trailer Fenders
- No Step
- 15 Inch Wheels
- 9 Inch Wide
- 32 Inch Long
- Steel
- Bolt-On
- Weld-On
- For Single-Axle Trailers
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: CE Smith Single Axle Trailer Fenders w/ Top and Side Steps - Black Plastic - 13" Wheels - Qty 2
- Shop: CE Smith Single Axle Trailer Fenders w/ Top and Side Steps - Black Plastic - 14" Wheels - Qty 2
- Shop: CE Smith Single Axle Trailer Fenders w/ Top and Side Steps - Gray Plastic - 12" Wheels - Qty 2
- Shop: CE Smith Single Axle Trailer Fender w/ Top and Side Steps - Black Plastic - 13" Wheels - Qty 1
- Q&A: Best Way For Connecting The Brown Side Marker Light Wire To A Boat Trailer
- Shop: Dexstar Steel Mini Mod Trailer Wheel - 16" x 6" Rim - 6 on 5-1/2 - Black Powder Coat
- Shop: HitchMate Boat Trailer Step - 5" Wide x 9" Long - 400 lbs
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Search Results: guide brackets
- Search Results: trailer jack
- Video: Checking Out the Valterra RV Waste Valve Cap
- Search Results: 16x6 wheel
- Search Results: valterra
- Q&A: Welding Instructions for Install of etrailer jack part # TJD-7000
- Search Results: stabilizer jacks trailer jack
- Search Results: drop jack
- Search Results: 6 on 55
- Video: Review of etrailer Trailer Jack - Car Hauler - Enclosed Trailer - Utility Trailer - e22ZV
- Video: Comprehensive Review: Square Drop Leg Stabilizer Jack
- Video: Complete Breakdown of the Square Direct Weld Jack w/ Footplate
- Article: Trailer Wiring Diagrams
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Shop: Brake Controller
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector





Ted
5/8/2018
Thanks...note this is a boat trailer so there's really not much room to weld. Do you sell a fender that you would recommend for standing on? I understand the bit about brackets, but they will be only on the bottom edge.