Replacement Plastic Cap and Seal for 8K EZ Lube Axle

Question

Question:

Do you carry a viton replacement seal for the plastic cap on a MorRyde IS 8K with easy lube?

asked by: Bill S

0

Expert Reply:

The Replacement Grease Cap for Kodiak 8,000-lb Disc Brake Kits # KPCAP is designed to fit a 2.25 inch spindle and has a thread outer diameter of 2-7/8 inch by 12 thread. We also have the Oil Cap, Plug and O-Ring for Dexter 7-9K Trailer Axles # RG04-230 with the same dimensions. We don't have the Viton O-ring outside of the cap replacement kit. Either of these will work on the EZ Lube axles.

expert reply by: Jason S

0

Answer 1

I spoke to my contact at Kodiak and they informed me that a socket should not be used when removing or installing the grease cap like part #KPCAP as this would likely cause damage to the polycarbonate material used in it's construction. If the…

view full answer...

Answer 2

The Kodiak Oil Cap #KPCAP you are looking at is a replacement cap for the Kodiak Pro Lube Kit. The oil cap you need is the Redline Oil Cap, Plug and O-Ring for Dexter 7-9K Trailer Axles #RG04-230. This will replace the oil cap on your trailer axles…

view full answer...

Answer 3

Yes, the Kodiak Disc Brake Kit #K2HR858AE will fit your Lippert 8,000lb torsion axle. Your Lippert axle uses a #42 spindle which is what the Kodiak brake kit is designed to fit. Do note that this kit uses 5/8" wheel studs and you may have…

view full answer...

Answer 4

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 5

Hey Priscilla, since you have a Dometic water heater that currently has a 16 inch by 16 inch door currently the correct Furrion Tankless Water Heater would be the part #FR32TD that you referenced which comes with this size door. Are you ready for…

view full answer...

Answer 6

It sounds like you're looking for a brake actuator that fits a 2" ball for your 2017 Trailstar. The dimensions don't have to match up, although it is nice if they do. The important thing is to know the capacity you need and whether this…

view full answer...

Answer 7

In terms of capability the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K #DX89FR is a good replacement option. The problem is the design of your old TDE LP7000 which was installed inside the tongue…

view full answer...

Answer 8

To replace your TDE Model LP7000 actuator, I recommend the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout item #DX89FR. This coupler is designed to mount on top of a standard 3" wide trailer tongue. It measures right at 3-3/8" wide so…

view full answer...

Answer 9

We have the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout #DX29FR for disc brakes and the Dexter DX7.5L A-60 Brake Actuator #DX27FR for drum brakes that will be a better option. These will have similar bolt patterns as your Tie Down…

view full answer...

Answer 10

Hey Brian, what pump setup are you using and are you sure that it's building pressure? Do you have a pump like the #ST93FR?

view full answer...

Answer 11

Typically a Dexter 7k axle will have a diameter of 3 inches and an 8k axle will have a diameter of 3-1/2 inches. The thicker the axle the more weight it can handle. There really isn't an advantage to going with higher capacity leaf springs than…

view full answer...

Answer 12

Though we do have the Bearing Buddy #BB2441T-SS that is a direct replacement for Tie Down's Turbo Lube oil baths, this will require you changing over to grease instead of oil. With that said, we do also have the Kodiak XL ProLube Kit…

view full answer...

Replacement Plastic Cap and Seal for 8K EZ Lube Axle

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching