Replacement Sidewind A-Frame Trailer Jack with 2 Inch Diameter
Updated 04/17/2018 | Published 04/14/2018
Products Featured in This Question
Question:
Hi I have a boat trailer with an a frame jack with side wind. I would like to replace it by buying one that matches and swapping out the insides so I dont have to cut up my trailer. There is a cap on the jack that says Fulton. The diameter of the tube is about 1 3/4. Do you have anything that is a little less than 2inch in diameter I could buy to swap out the internal stuff and have a working jack again?
asked by: Justin
Expert Reply:
The jack mounts used on a-frame trailers usually follow an industry standard pattern which is a 2-1/4" hole opening and three mounting holes spaced 3" apart. I have attached a photo to show this for you as well. If your trailer coupler does not follow this pattern and you indeed only have a 2" diameter hole to fit the jack through then I recommend using the A-Frame Trailer Jack part # DL22530 which has an outer tube diameter of 2".
As long as the tongue weight of your trailer does not exceed 1,000 lbs then this jack will work well for you. The jack offers up to 15" of travel, has a 3-year warranty, and is made right here in the U.S.A. If you would like to add a footplate or wheel to the jack you can do so using part # DL22541 for the foot or part # DL22414 for the wheel.
I have attached a review video of the above jack for you as well.
Product Page this Question was Asked From
Dutton-Lainson A-Frame Trailer Jack - Sidewind - 15" Lift - 1,000 lbs
- Trailer Jack
- Utility Trailer
- A-Frame Jacks
- Sidewind Jack
- 0 - 1000 lbs
- Manual Jack
- 15 Inch Lift
- Bolt-On
- Weld-On
- No Wheel or Foot
- Dutton-Lainson
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Video: Ultimate Overview of the A-Frame Trailer Jack
- Search Results: 2 inch tube jack
- Shop: Dutton-Lainson A-Frame Trailer Jack - Sidewind - 15" Lift - 1,000 lbs
- Q&A: Dimensions of Bulldog Powered Jack BD500199 and Dutton Lainson DL22530
- Q&A: Replacement Jack for Bulldog BD154107
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Trailer Wiring
- Search Results: trailer tires and wheels
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Comparing Kenda KR03, KR35, And KR53 Tires
- Search Results: trailer jack
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Shop: Suspension Enhancement
- Shop: Power Mountain Tallboy Off-Road Bottle Jack - 8-1/2" to 37-3/4" Lift - 6 Tons
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Search Results: trailer wiring
- Shop: Brake Controller
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Shop: Gooseneck Hitch
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Best Suspension Upgrade for 33" Tandem Axles: Road Armor vs Dexter EZ Flex for Ember 22ETS
- Shop: Trailer Wheel Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Search Results: trailer lights
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 12" - Left/Right Hand - 5.2K to 7K
on Camper Jacks
