Wheel Chock and Tie-Down Straps for Smaller Honda CRF-110 Dirt Bike

Question

Question:

Hi there Would those wheel chocks work on a Honda CRF-110? It’s a smaller kids bike so I’d like to make sure it will work before buying. Thanks

asked by: Brian

0

Expert Reply:

Our range of motorcycle wheel chocks is shown on the linked page. These do vary a bit in terms of the compatible wheel diameters and widths. For a smaller dirt bike you'll likely be better off using the Rack'Em Manufacturing Removable Wheel Chock # RA-17 for the 110's 70/100-14 front tire.

You may also care for some tie-down straps such as # EM05710.

expert reply by: Adam R

0

Answer 1

From what I was able to find, the interior dimensions of your 2012 Sprinter are 72" x 70". You could use a cargo net like the Gladiator #GC94FR which is 6' 9" x 8'. There will be a little extra but nothing overly excessive. It…

view full answer...

Answer 2

The Curt RockerBall Anti-Rattle Towing Kit #C43KR takes the additional height of the base of the RockerBall into account for the listed 4" rise and 5" drop. I have attached an image below showing how it is measured. Typically, you find the…

view full answer...

Answer 3

Hey Matt! The Curt RockerBall Anti-Rattle Towing Kit #C63KR has a 3" drop with the extra height from the ShockDrop. See the attached photo. Are you looking for a certain rise/drop? What kind of trailer are you towing?

view full answer...

Answer 4

Hey Karl, we have a similar option with the part #BWTS10035B that is what you are looking for as it has a 2 inch and a 1-7/8 inch ball but we don't have a Curt ball mount with those two ball sizes.

view full answer...

Answer 5

It sounds like you are trying to get the best hitch mounted suspension for your vehicle to not transfer the shock. The Gen-Y Glyder Shock Absorbing Ball Mount for 2" Hitches - 2" Drop, 3-1/2" Rise - 7K #325-GH-12001 will absolutely…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

There sure is K.C.. For a shorter weight distribution shank that fits a 2-1/2" hitch, I recommend the Equal-i-zer item #EQ90-02-4700. This shank measures 12" long x 9-1/2" tall. It provides up to a 3" drop and has a 16,000 lbs…

view full answer...

Answer 11

Hey Rob, I’d be wondering the same thing if I came across a ball mount made out of aluminum like the #BPH77MR while researching. Totally fair question. That said, I haven’t seen any noticeable difference in slop or wear compared to their steel…

view full answer...

Answer 12

The appropriate torque spec for any application will vary depending on the construction of the wheel as well as on the stud size. I suggest checking the wheels you're using to see if their manufacturer has a suggested torque rating. Steel trailer…

view full answer...

Wheel Chock and Tie-Down Straps for Smaller Honda CRF-110 Dirt Bike

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching