Trailer Jack Recommendation for Kendon Motorcycle Trailer with Round Tongue

Question

Question:

Thank you for the quick response. Can you suggest one that has a whee

asked by: Marcelo

1

Helpful Expert Reply:

There is no bolt-on jack made for a round tube trailer frame since this would make securing the jack rather difficult; it would want to rotate around the frame tube whenever it was under load.

You will need to have some steel material welded to your frame to allow jack installation. You can use a pipe-mount type like Pipe Mount Swivel Jack # DL22685 which includes the weld-on pipe section.

expert reply by: Jameson C

1

Marcelo

2/16/2018

Thank you for the quick response. Can you suggest one that has a whee

Jameson C.

2/16/2018

For that you'd need the Bulldog Jack part # BD1541150301, the pipe mount # BD015279, and the wheel caster part # BDCP555.

Sam R.

5/29/2024

@JamesonC In the part numbers thread above, I can’t seem to locate pipe mount BD015279, is this item # still correct, or out of stock?

Jameson C.

5/29/2024

@SamR That part number is no longer available to us so we can't get it anymore.

See All (5) Replies to Marcelo ∨

Answer 1

Hi Rick, What you're referring to is a snap ring swivel plate which would require the appropriate mounting plate being welded to the jack. Instead you can use the etrailer Bolt-On Swivel Mounting Plate #e52JR to attach the Bulldog Round,…

view full answer...

Answer 2

Since you have only 2-3/4" between the coupler of your trailer and a steel beam I recommend the Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 10" Lift - 2,000 lbs #BD1541150301 which will only take up about 2-1/2" of space on the…

view full answer...

Answer 3

There is no bolt-on style jack made for a round tube trailer frame since this would make securing the jack rather difficult. The jack would want to rotate around the frame tube whenever it was under load. Your only option is to weld a jack mount onto…

view full answer...

Answer 4

I'm assuming you're speaking of an anti-rattle device. Many anti-rattle devices depend on the receiver tube to have a lip around it. The Roadmaster #RM-061 or the Brophy #RSCP are examples of this type. An anti-rattle device like the #63232…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Trailer Jack Recommendation for Kendon Motorcycle Trailer with Round Tongue

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching