Can Redline Trailer Wheel Bolts be Used With Aluminum Wheel?

Question

Question:

I have a zieman trailer that uses this lug bolt. Can I use one of the aluminum rims that you sell or do I need to stick to a steel rim? Thank you

asked by: Dean B

0

Expert Reply:

The Redline # RG02-020 trailer wheel bolts are 1/2" diameter x 1" long and you would be able to use them with aluminum wheels. I've added a link to our selection of aluminum wheels for you to take a look at as well.

expert reply by: Kyle S

0

Answer 1

The correct torque specs for the wheel bolts like part #RG02-020 on your trailer with 13" wheels will be dependent on their diameter. I have attached a chart for you below with these variables. These torque specs will be the same whether you…

view full answer...

Answer 2

Thank you for the photo of your vintage trailer hub. This type of hub uses bolts rather than lug nuts to secure the trailer wheel. We offer kit #RG02-020 which consists of four (4) 1/2-inch x 1-inch 60-degree-coned wheel bolts. We also have a kit #…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Can Redline Trailer Wheel Bolts be Used With Aluminum Wheel?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching