Diameter of the Replacement Handle Shaft Part # TJD-12000-SHABUS

Question

Question:

What is the outside diameter of the shaft and the interior diameter of the bushing?

asked by: Ron

1

Helpful Expert Reply:

I went out to our warehouse and measured the Replacement Handle Shaft part # TJD-12000-SHABUS for you. The outer diameter of the shaft is exactly 1.00" and the inner diameter of the bushing is just slightly larger measuring exactly 1.02".

I have attached a few photos with the above dimensions shown for you as well.

expert reply by: Conner L

1

click to enlarge

Answer 1

Here is a list of the replacement parts we have for the Ram 12K Support Capacity Jack #TJD-12000SP-F2 you found. Replacement Sidewind Crank #TJD-12000-HD Replacement Plunger Pin Assembly #TJD-12000-PPN Replacement Cap #TJD-12000-CP Replacement Return…

view full answer...

Answer 2

Hey John, the replacement gear kit you'd need is the part #TJD-12000-RODNUT which I attached two pictures that have instructions and an install diagram.

view full answer...

Answer 3

The #BD500212 is specifically made for Bulldog jacks. Based on the 12,000 lb capacity and 10,000 lb lift on your Ram jack it sounds like you have a TJD-12000 series jack like the #TJD-12000SP-F2. The correct gear kit would be the #TJD-12000-GR. If…

view full answer...

Answer 4

I went ahead and linked the video you are referencing about rebuilding a square jack like the Square Direct Weld Jack #TJD-12000SP-F2 from our website to this answer. We have a number of replacement parts in that video and some that were not included…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Diameter of the Replacement Handle Shaft Part # TJD-12000-SHABUS

Product Page this Question was Asked From

Continue Researching