Trailer Hitch Availability for 1999 Ford Taurus Wagon

Question

Question:

I need a class 3 that goes on to a 1999 ford taurus wagon se.

asked by: Mike

1

Helpful Expert Reply:

For your 1999 Ford Taurus wagon we only have Class II hitches like the Curt part # C12232 which is a confirmed fit. The Class III hitches are only used on vehicles with higher capacities like trucks and SUVs.

I attached the instruction video for this hitch for you to check out as well.

expert reply by: Jameson C

1

Answer 1

That is not correct. The Hopkins #HM48895 should not be overriding the turn signals when the brakes are applied. I would just for the heck of it doublecheck the wires on the truck that you spliced into for the turn signals, and brake signal, as…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 5

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

Hey George, for your 2026 Toyota RAV4 Hybrid we have the Curt hitch part #C34FR62ZY as a confirmed fit but it's on a little bit of a backorder at the moment which is why you don't see any hitch options in our fitguide. The hitches from…

view full answer...

Answer 8

Hey David, thanks for reaching out. Yes, the Curt Trailer Hitch Receiver #C82RJ will indeed fit the 2027 Kia Telluride. This hitch is still in the pre-order phase, but it is being going to fit both the 2026 and 2027 Telluride. Right now, we are…

view full answer...

Answer 9

Hello Mike, thanks for reaching out. We do offer a few different hitches for the 2026 Subaru Crosstrek, the Curt #C22MJ, the Draw-Tite #76209 and the EcoHitch #EH57CR. All 3 of these hitches place the receiver in virtually the same position beneath…

view full answer...

Answer 10

Hey Adrian! The higher capacity for the B&W #BW47BR and Curt #C77MJ comes from the construction. The B&W hitch weighs 45 lbs and then the Curt and Trailer Mate #TMT54FR both weigh 32 lbs. The Trailer Mate does sit just a tad higher compared…

view full answer...

Answer 11

Hi Richard! Yes, the Curt Trailer Hitch Receiver #C37RV will fit your 2026 Santa Fe Hybrid. The installation process will be the same. We actually installed this on a 2025 hybrid so you can use that as a guide. I attached a link to the video further…

view full answer...

Answer 12

Hey Jason! The etrailer #e69ZV and Curt hitch do share the same design. Our hitch has the same restrictions so you do not want to use it for that bike rack. Instead, you can use the TowSmart Trailer Hitch Receiver #TS48QR. This also has a higher…

view full answer...

Trailer Hitch Availability for 1999 Ford Taurus Wagon

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching