Can a Timbren Suspension Kit be Used with Weight Distribution System

Question

Question:

on a 2017 4x4 1500 silverado crew cab with max towing can i use timbren with wdh i tow 30 ft tt i know you dont recommend on other vehicles

asked by: John

0

Expert Reply:

Yes, you can use a Timbren system like the part # TGMRCK15S with a weight distribution hitch on a 2017 Chevy Silverado 1500.

If you have the WD system already you'll have to go through the setup process again after the Timbren install since you'd need less spring bar tension.

expert reply by: Jameson C

0

Answer 1

The correct Timbren Rear Suspension Enhancement System for a 2003 GMC Sierra 1500 LD is part #TGMRCK15S for extended or regular cab models and part #TGMRCK25S for crew cab models. The springs once installed should be anywhere from 1/2" -…

view full answer...

Answer 2

Per the manufacturer's recommendations, there should be approximately 1"-1.5" of clearance between the rear contact point and the Timbren Rear Suspension Enhancement part #TGMRCK15S when not under load. Too little space will cause the…

view full answer...

Answer 3

As for comparing the Timbrens #TGMRCK15S to the Roadmaster Active Suspension Custom Leaf Spring Enhancement Kit #RAS54FR on your 2021 Chevy Silverado 1500 (4x4), the answer really depends on how much you tow or need suspension support for your Chevy.…

view full answer...

Answer 4

Suspension enhancement would be a good idea to get rid of the squat you are experiencing when towing with your Fastway E2 weight distribution system. The best option is the RoadActive Suspension kit part #RAS54FR which gives you the support you want…

view full answer...

Answer 5

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 6

For a weight distribution system, there are always exceptions,but in general the systems with only bars and chains do not have sway control. They are adjustable in tension for different weight, but are a little more work. The bar systems whether…

view full answer...

Answer 7

I found the article you mentioned from Timbren and a 1 inch gap is recommended for the rear kits but for the front kits they recommend no gap at all. Since the part #TGMFK25D is a front kit you'd want to not have any gap at all.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Can a Timbren Suspension Kit be Used with Weight Distribution System

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching