Does Curt Spyder Above-Bed Gooseneck Come With Pins For Installation

Question

Question:

Are pins, included with the Curt Spyder? The pictures show the kit, but want to make sure!

asked by: Leanne M

0

Expert Reply:

Definitely a good idea to know what you're getting and yes, the attachment pins absolutely do come with the Curt Spyder Gooseneck Trailer Hitch for Fifth Wheel Rails - 30,000 lbs # C35HR.

expert reply by: Kyle S

0

click to enlarge

Answer 1

The Curt Spyder Gooseneck Trailer Hitch for Fifth Wheel Rails #16085 sits 7-1/2 inches above the rails at the highest point. The Curt Above-Bed Gooseneck Trailer Hitch for Fifth Wheel Rails - 3" Offset #16055 will sit lower with the top of the…

view full answer...

Answer 2

Your fifth wheel rails with the CMI stamped on them were manufactured by Curt, and will be compatible with Curt, Draw-Tite, Husky, Reese, Valley, and other brand hitches. They fit what are called industry standard hitches. For your 2008 Ford F-350, I…

view full answer...

Answer 3

It sounds like you could have a set of standard fifth wheel rails that most manufacturers use for their fifth wheel hitches to install into. The different manufacturers all make their own brand of rail kit, but they all have basically the same…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Does Curt Spyder Above-Bed Gooseneck Come With Pins For Installation

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching