Should Loctite be Used on Americana Valve Stem?

Question

Question:

Do you recommend to use or not use loctite on the nut of the AM20906? Also, to confirm, it looks like the washer is installed with the center ridge convex side to the nut... correct?

asked by: Kent

0

Expert Reply:

It would not be necessary to use Loctite on Americana valve stem # AM20906. You will need to be sure to torque it properly, which is recommended to be between 25 and 55 inch-pounds. And in regards to your second question, you are correct about the installation in regards to the nut.

expert reply by: Kyle S

0

click to enlarge

Answer 1

The importance of matching a wheel's pilot hole diameter to the part of the hub that fits through it depends on the type of wheel. A hub-centric wheel uses the pilot hole to center the wheel on the hub and also to bear some of the total weight…

view full answer...

Answer 2

The hub bore diameter close to the base of the Dexter Trailer Idler Hub Assembly for 6,000-lb Axles #42655UC1 is just over 3-1/2". Please note that the hub you're asking about is a lug-centric hub which means it has the studs in place and…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

I apologize for any confusion on what the proper torque specs are for 1/2 inch lug nuts on trailer wheels. I attached a picture of a chart to the right that details what the proper torque specs are for a trailer wheels lugs based on lug size, wheel…

view full answer...

Should Loctite be Used on Americana Valve Stem?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching