3/4 Inch Conical Tooth Washers for Fastway e2 Weight Distribution Systems

Question

Question:

Can this conical 3/4inch washer set be used with a fastway e2 6000 wdh? What is the difference between these washers and your part number 3232 washer?

asked by: Patricia A

1

Helpful Expert Reply:

Curt Weight Distribution Conical Washer Replacement Kit Item # C17314 is not a confirmed fit for the Fastway weight distribution systems but I am certain they would work. Other than the manufacturer there isn't much, if any, difference between the Curt washers and Draw-Tite 3/4" Conical Tooth Washer Item # 3232.

expert reply by: Michael H

1

Answer 1

Hi Todd! Nice truck! ^___^ I can definitely get your 2020 Tundra SR5 squared away with suspension enhancement and a weight distribution system that will get you towing your Lance 2565 comfortably. To start with, I recommend the Air Lift LoadLifter…

view full answer...

Answer 2

The Lead Jack Repair Kit #LG-146059 that contains the drive pin 920-00 that you referenced comes in a kit and isn't available as separate parts unfortunately. To get the replacement drive pin you will need to get the whole kit.

view full answer...

Answer 3

If the teeth have smashed, you'll want to replace those washers. Fastway doesn't offer them as an individual replacement part, but they are included with the #FA92-02-9600 replacement hardware/service kit. Without washers that get a good…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

3/4 Inch Conical Tooth Washers for Fastway e2 Weight Distribution Systems

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching