Will Bargman # 47-86-202 Replace # 48-86-202

Question

Question:

I am looking for a Bargman 48–86-202. You list a 47-86-202. Both look similar but what is the difference between the two? Or would both fit? Thank you.

asked by: Dan A

1

Helpful Expert Reply:

Yes, the # 47-86-202 would be the same thing as the part 48–86-202 that you mentioned and would work well.

expert reply by: Jameson C

1

Answer 1

Yes the Replacement Lens for Bargman 86 Series Wraparound Clearance/Side Marker Lights part #30-86-711 you were looking at is the correct replacement for the discontinued Bargman Series 86 Wraparound Lights. These lights will work on both passenger…

view full answer...

Answer 2

The process to install the Pulse Preventer for Electric Brake Controllers part #5501 on a vehicle with factory brake controller port entails locating the stop light switch wire in that harness (usually red) and splicing into this between the brake…

view full answer...

Answer 3

It sounds like you wired the brakes into the combined stop/turn signal circuit on the trailer. Trailers use what is called a combined system meaning that the brake lights and turn signals are on the same tire. So when you are using the turn signal…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Will Bargman # 47-86-202 Replace # 48-86-202

Continue Researching