See what our Experts say about this Lippert Camper Jacks

• Replacement Parts for Lippert Electric Stabilizer Jack
  There are not replacement legs available for the Lippert Components High-Speed Power Stabilizer Jack - White Switch Kit - 30" Lift # LC369774 which is the same as the 198641 you mentioned. You will need to replace the entire unit. The support arm # LC1134122 in yellow or # LC1134121 in black is the only non-electric component able to be separately replaced. The motor # LC138445, circuit breaker # LC134181, and switches # LC144214 or # LC387874 as well as switch housing # LC134025 are...
  view full answer...
• Recommended Stabilizer Jacks for 2018 Forest River Shockwave Travel Trailer
  It sounds like you are looking for stabilizer jacks for your 2018 Forest River Shockwave travel trailer. Landing gear is something you would typically find on a 5th wheel. If you are looking for some manual jacks for the rear then I recommend the Ultra-Fab Ultra Scissor Jacks # UF48-979002. If you're looking for electric stabilizers then I recommend the Lippert High-Speed Power Stabilizer Jack - White Switch Kit - 30" Lift # LC369774. This features legs that extend up to 30" for quick...
  view full answer...
  
• Troubleshooting Lippert Electric Stabilizer Jacks Not Lowering
  The collar being loose on your stabilizer jack may be the issue as that is part of the motor assembly. The motor directly connects to the threaded rod so with that being loose it may have broken off and disconnected from the threaded rod. I recommend removing the motor, and checking it for correct function. If the motor collar or shaft has broken and needs replacing, you can use the Replacement Electric RV Stabilizer Jack Motor for Lippert Components Landing Gear - Rear # LC352338. ...
  view full answer...
• Replacement Jacks for a LCI model 377199
  Hey Jim. To replace your LCI model 377199 you can use the Lippert High-Speed Power Stabilizer Jack item # LC369774 or item # LC298707. The Lippert 377199 is no longer available but the item # LC369774 or item # LC298707 are the modern replacements. They come with different power switches but the jacks are identical. If you don't need the power switch, I would just go with the least expensive option. They measure 78" long and has a 30" lift. The mounting hole spacing on both jacks is 68-11/16"...
  view full answer...
• Troubleshooting Lippert PSX1 Stabilizer Jacks Not Working
  I can help you troubleshoot, Patrick! Your Lippert PSX1 Stabilizer Jacks, replaced by the Lippert # LC369774, has a few reasons why it might stop working: 1 - Too much weight (circuit will reset in 10 seconds) 2 - Low Voltage (test battery voltage under load) 3 - Damaged or disconnected wiring (check wiring and repair/replace) You should still be able to use the manual override just fine, but if none of this fixes the issue let me know and I can continue to help you troubleshoot.
  view full answer...
• Electric Leveling Jack for a 2019 Jayco Redhawk Motorhome
  Thanks for reaching out, Mary. Congrats on the new camper! You definitely have options for adding an electric leveling system to your 2019 Jayco Redhawk, and something like the Lippert High-Speed Power Stabilizer Jack # LC369774 would work really well for your setup and would be able to handle the weight of your RV. One nice thing about this system is that it’s a universal fit, so you won’t have to worry about it being tied to one specific motorhome model. It also automatically adjusts...
  view full answer...
• Replacement Jack or Support Arms for Lippert PSx1 Stabilizer
  For your Lippert PSx1 Stabilizer, the Replacement Electric Stabilizer Jack Support Arm part # LC1134122 is what you need if you are looking to simply repair your jack. If instead you are looking to replace the entire unit then the Lippert Components High-Speed Power Stabilizer Jack - Black Waterproof Switch Kit - 30" Lift # LC298707 or the version with white switch # LC369774.
  view full answer...
• What Stabilizer Jack do I Need to Replace Mine on My 2018 Keystone Impact Fuzion LCI 337199?
  Hello David, Congratulations on the new camper! Where did you take the Keystone for its first trip to break it in, or are you tackling a few repairs before hitting the road? I just got back from the Valley of Fire near Las Vegas last week, and it was absolutely breathtaking! You’re correct that the LCI 337199 is no longer being produced. The Lippert High-Speed Power Stabilizer Jack – White Switch Kit – 30" Lift # LC369774 is the best current replacement option to swap it out.
  view full answer...
• Electric Leveling Jacks For Class C Motorhome
  Hi Kristina; the closest thing we have for a Class C motorhome is the Ultra-Fab Power Twin II Electric Stabilizer for Trailers and RVs # UF39-941707. This is similar to the # LC369774 you were looking at but fits frames from 42" to 77" wide. The Lippert system has mounting hole spacing of 68-11/16" from center-hole to center-hole which limits the application. These are designed as stabilizers but you can level your motorhome using the separate switches. Also, it won't be automatic leveling...
  view full answer...
• Looking for Replacement Stabilizer Jacks for RV Lippert 298707
  Hey Laine, the current replacement for the now discontinued 298707 would be the Lippert # LC369774. When you say estimate are you looking for a price estimate for just the replacement jack or estimate on time?
  view full answer...
• Is There Stabilizer Jack that Can Work on Class C Motorhome that has 42-1/4 inch Wide Frame
  Hey Rayneil, the mounting holes of the Lippert Stabilizer Jack part # LC369774 that you referenced are 68-11/16 inches apart which would be a lot wider than the dimensions of your motorhome frame. Instead we do have one option that will work for you with the Ultra Fab Stabilizer Jacks # UF39-941707 as it will work on RV frames that are between 42 and 77 inches. This is our only option that will work but it also happens to be a really nice stabilizer as well so you'll really like it.
  view full answer...
• Leveling Stabilizer Jack that Can be used with 2021 Sprinter RV Camper
  Hey Jody, for motorhomes the best option for a leveling jack setup is the Lippert High Speed stabilizer leveling jack part # LC369774 which allows you to level and stabilize by just pressing a button.
  view full answer...
• Stabilizer Jack that Can Fit 2018 Starcraft Autumn Ridge 5th Wheel
  Hey Nathan, there is a very good chance the Lippert High Speed Power Stabilizer part # LC369774 will fit your 2018 Starcraft Autumn Ridge Fifth Wheel as it was designed to fit as many RVs as possible but unlike cars there isn't info on exactly what your RV would need/use. Instead you'd have to measure your RV frame width and check to see if the mounting hole spacing of this kit at 68-11/16" from center-hole to center-hole would work. If that doesn't work we have the part # UF39-941704...
  view full answer...
• Difference Between Lippert High-Speed Power Stabilizer Jack LC298707 and LC369774
  Hi Terry; the only difference between the Lippert High-Speed Power Stabilizer Jack # LC369774 and # LC298707 is the switch kit. The # LC369774 has the standard white switch with the housing while the # LC298707 has the black waterproof switch. The actual stabilizer jack is the same for both. This has mounting hole spacing of 68-11/16" from center-hole to center-hole so you will need to measure to be sure it fits.
  view full answer...
• Is There a Replacement Leg for the Lippert Stabilizer Jack 198641
  I do have a solution for you to have a working stabilizer again but unfortunately when I spoke with my contact at Lippert he said that the legs on your 198641 unit are not replaceable alone. Instead you will need to replace the whole stabilizer jack with part # LC369774.
  view full answer...
  
• Does Lippert High-Speed Power Stabilizer Jack Have a Weight Capacity
  The Lippert High-Speed Power Stabilizer Jack # LC369774 don't have a weight capacity because it is designed to essentially just fill the gap between your trailer frame and the ground - this isn't meant to lift the trailer so they haven't given it a specific rating. For a stabilizer with this same design that is built to lift the trailer then the Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors # UF39-941705 is what you're needing. This is has a weight capacity of 6,000 lbs. If...
  view full answer...
• Recommended JT Strong Arm Stabilizer Kit with Adapter Kit for Lippert Power Jacks
  For your Lippert power jacks like # LC369774, you will want one Lippert Components JT's Strong Arm Jack Stabilizer Adapter Kit for Electric Stabilizer Jacks # LC314597 for two Lippert jacks. You will use one tab on each foot to allow clearance for correct operation. It sounds like you have two Lippert power jacks, but you will only need one JT Strong Arm kit and one adapter kit. This will allow you to use the Lippert Components JT's Strong Arm Jack Stabilizer Travel Trailer Kit # LC191025....
  view full answer...
  
• Does The Replacement Switch LC144214 Come With Wires Pre-Attached?
  Yes, your new white switch # LC144214 will come with the wires pre attached to the back. I have included a a wiring diagram below which will show you how to wire the new switch to the motor. We would generally use butt connectors, preferably heat shrink, to connect the wires.
  view full answer...
  
• Differences Between the Lippert Components Power Stabilizer Trailer Jacks
  You made a great choice in the Lippert Components Power Stabilizer Trailer Jack. For starters, all of the jacks measure to be 70-1/2" long with a 3,500 lb weight capacity and have a 30" lift. The difference between them is in regards to what is included with them. The part # LC369774 comes with a white switch and part # LC298707 comes with a black switch. That is the only difference.
  view full answer...
• Replacement for Lippert PSX2 Stabilizer Jack 695602
  I do have an option for you but we don't carry the Lippert PSX2 Stabilizer Jack 695602. Instead, we carry the Lippert High-Speed Power Stabilizer Jack part # LC369774 for a white switch, or part # LC298707 for a black switch. These are very similar jacks to what you have now expect they have a single motor design. The footprint and mounting will be the same.
  view full answer...
• Replacement Stabilizer Legs For Lippert Power Stabilizer
  On the Lippert High-Speed Power Stabilizer Jack 337199 it would appear that the only parts of the legs that are replaceable are the Electric Stabilizer Jack Support Arm # LC1134122 and the Foot Assembly # LC157584. If the black arms are buckled then the entire jack assembly will need to be replaced. Since the 337199 is no longer available you will need the Lippert High-Speed Power Stabilizer Jack # LC369774.
  view full answer...
• Wiring For Lippert Components High-Speed Power Stabilizer Jack
  I assume you are asking about wiring the switch of the Lippert Components High-Speed Power Stabilizer Jack # LC369774. For this, please refer to the accompanying cutout I added; your jack uses Switch # LC144214 so as the diagram makes clear, the black wire is retract, the green wire is extend, the white will likely be ground and red will then be power.
  view full answer...
  
• Replacement Stabilizer Jack Need for Lippert Model 113407
  The direct replacement for your Lippert Model 113407 stabilizer jack is part # LC369774. I confirmed this with my contact at Lippert. It requires an easy bolt-on installation.
  view full answer...
  
• Replacement Recommendation for Lippert PSX1 Electric Stabilizer Jack
  The Lippert Stabilizer Jack 347132 (discontinued part LC363284 on our site) has mounting hole centers that are 68-11/16" apart which is the same as our High-Speed Stabilizer Jack # LC298707 so it can definitely be used as a replacement! The High-Speed jack part number I mentioned above is the jack itself. If you're also needing the control switch, then we have part # LC369774 which comes with a white switch or part # LC298707 which comes with a black switch. Attached is a review video...
  view full answer...