Is Drilling Required When Installing the SumoSprings Maxim Springs on a 2016 Fleetwood Bounder 35K

Question

Question:

2016 fleetwood bounder 35k sumo helper springs is there any drilling required to install these springs

asked by: Ed B

0

Expert Reply:

The SumoSprings Maxim Custom Helper Springs # SSR-180-54-1 for the rear axle on your 2016 Fleetwood Bounder 35K do not require drilling. SumoSprings are an excellent choice for suspension enhancement because there is no maintenance. You install them and then do not have to worry about them!

If you are putting suspension enhancement on your RV I also recommend putting it on the front axle as well. A great no-drill option from Super Springs would be the SumoSprings Rebel Custom Helper Springs # SSF-170-40-2 which replace your factory bump stops.

expert reply by: Jon G

0

Answer 1

You can install a front set of SumoSprings on your 2019 Jayco Precep 29V if you wanted first with the part #SSF-170-40-2. It will give you improved handling and stability and then for the rear then #SSR-180-54-1 and you'd be set. Having the front…

view full answer...

Answer 2

If you wanted to install SumoSprings on your 2017 Fleetwood Bounder built on a Ford F-53 that are designed for the higher GVWR chassis you could but you should note that it would probably give you a harsher ride quality than you'd want. For GVWR…

view full answer...

Answer 3

The jounce springs I recommend for your two wheel drive 2019 Ford F-53 chassis are from SumoSprings, the SumoSprings Rebel for the front axle and SumoSprings Maxim for the rear axle. The reason why the SumoSprings are the best is because they not…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

Hey Kevin, yes we have the SumoSprings kit part #SS46KJ that is a fit for your 2025 Chevrolet Silverado 2500 HD. This is the medium density foam spring provides 2,800-lb support capacity at 50% compression and also requires no drilling for install!…

view full answer...

Answer 8

Hi Paul! Since you said occasional towing, I am going to steer you away from the Timbren option. They can be pretty rough and you will definitely feel it when you are not towing. If you had a constant load, it would have been an option, but I…

view full answer...

Answer 9

Hi Tim, That's a great question! While Timbrens and SumoSprings are both suspension enhancements, they perform differently depending on how much weight you're towing/hauling and how often you're planning on towing/hauling. The only…

view full answer...

Answer 10

Hey Steve! You need to leave the breakaway pin installed in the Curt RVibrake Shadow 2 #RVI94FR. The breakaway operates independently for safety, so even if you're disconnected from an RV it will activate the vehicle brakes. The only way around…

view full answer...

Is Drilling Required When Installing the SumoSprings Maxim Springs on a 2016 Fleetwood Bounder 35K

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching