Metal Mounting Bracket for P3 Brake Controller # 90195

Question

Question:

I have a Tekonsha Prodigy P3 trailer brake controller. I need a replacement metal mounting bracket bracket. Will part # P7685 fit my controller?

asked by: Brad T

0

Expert Reply:

For a metal mounting bracket that can be used with the P3 brake controller # 90195 you can use replacement bracket # 2178. Or you can use Replacement Mounting Bracket Kit # TK5906. If you need just the small metal bracket that attaches to the top of the plastic bracket it is # TK5904.

expert reply by: Michael H

0

Answer 1

I have 2 part numbers for you to replace the cradle for your Tekonsha Prodigy P3. Part #TK5901 is the cradle, #TK5904 is the bracket that screws into the dash. You would have to assemble these to parts to have a complete mounting bracket.

view full answer...

Answer 2

Hey Ken, we've heard that the wiring might be present but the circuits aren't complete and it's been kind of a confusing headache since. Looks like you bought the harness and controller and it shipped a couple days ago so if it works for…

view full answer...

Answer 3

Hey Matthew, thanks for reaching out! We do actually carry a plug-in adapter for installing the Tekonsha Prodigy P3 #90195 on your 2020 Silverado 1500. What you're looking for is the Wiring Adapter #3064-P. Is the Prodigy P3 brand new, or are you…

view full answer...

Answer 4

Hey Dave, yes we do have the bracket you are looking for with the part #TK5906 that fits the Prodigy P3 part #90195.

view full answer...

Answer 5

That's understandable; the Tekonsha P3 #90195 is one of our most popular and well reviewed brake controllers for a good reason. You can use the replacement bracket #TK5906 to mount the P3 in your new 2019 Toyota Tacoma. You can use this, with the…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Hey Lucas! I measured the Buyers Products Weld-On Receiver Tube #337RT25824B in our warehouse using my digital caliper, and it has an exact outer diameter of 2.54", so I don't believe it will work with your truck's 2-1/2" receiver.…

view full answer...

Metal Mounting Bracket for P3 Brake Controller # 90195

Continue Researching