2006 Holiday Rambler Navigator Brake Controller Install Recommendation

Question

Question:

Hi I believe my 2006 Navigator is wired for a brake controller but I cant seem to find where the wire is at on my coach. On my other coaches the wire was tied up under the dash with a tag indicating what is was. Any help would be appreciated. Thanks

asked by: FRANK A

0

Expert Reply:

On some Holiday Ramblers the wiring port for a trailer brake controller can be found under the left side control panel next to the driver's seat. The four wires should be +12V (black), brake switch signal (red), brake output (blue) and ground (white). On others it can be located under the left side of the dash and labeled "Brake" with 6 wires. Check there and let me know if you can find it.

For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller that senses the amount of braking the tow vehicle is applying and applies a proportionate amount to the trailer brakes. This will be the last brake controller you buy. It can easily be transferred to future vehicles as well.

expert reply by: Jameson C

0

Answer 1

I assume your 2002 Holiday Rambler Endeavor already has a 6-pin wiring harness in the back so you will need to cut that and connect it to the Universal Brake Controller Wiring Kit #ETBC7 using a circuit tester such as #PTW2993 to test the functions.…

view full answer...

Answer 2

The correct harness to use on your 2006 Holiday Rambler that is built on the Ford F-53 Chassis is the part #3034-P for installing a Tekonsha brake controller. The port to plug in a brake controller is up under the dash behind the instrument cluster.…

view full answer...

Answer 3

The best way to confirm the presence and location of a brake controller installation port in your 2006 Holiday Rambler Ambassador is to provide the coach's VIN to the manufacturer so that they can confirm which model year of base chassis was used…

view full answer...

Answer 4

A brake controller like the Tekonsha P3 will work just fine with the air braking system on your motorhome. The controller will get its input from the brake stoplight switch, which tells it when the brakes are being applied. If there is a 7-way…

view full answer...

Answer 5

For your 2000 Holiday Rambler Admiral, I recommend the Tekonsha Prodigy P3 #90195 brake controller. To install this, you can use the wiring harness #3035-P. For most applications, the factory plug is located beneath the dash, near the center console.…

view full answer...

Answer 6

To duplicate the Universal Installation Kit for Trailer Brake Controller, #ETBC7, minus the 7-way, you will need the Wiring Kit for 2, 4, 6 and 8 Brake Electric Brake Controllers, #5506, Hopkins Trailer Wiring Installation Kit, #HM51010, 40 amp.…

view full answer...

Answer 7

There is not an adapter harness for your 2007 Lexus GS430. To hardwire this controller to your system you can use the Replacement Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controller 12" Long #20127 to allow you to use the…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Hi Andrei; yep, you're 100 percent right, you should use the 30 amp breaker. That's why for the installation kit I recommend using the Universal Installation Kit for Trailer Brake Controller #ETBC7. The #ETBC7 comes with multiple breakers,…

view full answer...

Answer 10

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 11

I recommend using at minimum a 12 gauge wire like #12-1-1, but preferably 10 gauge wire like #10-1-1. When you try to run 12v power for electric brakes through a thinner 14 gauge wire to power something like your brakes it overloads the wire and…

view full answer...

Answer 12

On an 4 foot long section of E-track #EM19147 and 2 screws every 16 inches that is a total of 6 screws in the aluminum frame. This most likely will not get you near the capacity of the E-track. I recommend bolting through the aluminum frame so that…

view full answer...

2006 Holiday Rambler Navigator Brake Controller Install Recommendation

Continue Researching