Installing A Brake Controller On A 2000 Holiday Rambler Admiral

Question

Question:

I own a 2000 Holiday Rambler Admiral and am having trouble locating the wire in the coach to tap into...please advise.

asked by: Tami S

0

Expert Reply:

For your 2000 Holiday Rambler Admiral, I recommend the Tekonsha Prodigy P3 # 90195 brake controller. To install this, you can use the wiring harness # 3035-P. For most applications, the factory plug is located beneath the dash, near the center console. You may also need the Ford Replacement OEM Tow Package Wiring Harness, 7-Way (Super Duty) # 118243.

If you don't have the ability to add a simple harness in your coach, you can use the circuit tester # PTW2993 to check for function. You will need a 12V constant power, the cold side of your brake light switch found near the brake pedal, a clean ground to your coach, and then the brake output from your controller to the rear of your coach. If you need to hardwire your controller, you can use the # ETBC7 for the complete system or the # 5506 if you already have the 7-Way.

I've attached a diagram to assist.

expert reply by: Jason S

0

Answer 1

A brake controller is going to need to be hardwired into your 2002 Holiday Rambler Endeavor because there is no plug available. In order to do this (since I assume it already has a 6-pin wiring harness in the back) you will need to cut that and…

view full answer...

Answer 2

Since you already have a 6-way on the back of your 2001 Holiday Rambler Imperial it's possible there's already a brake circuit. However, since the previous owner was towing a vehicle it may not and you'll need to check for a wire running…

view full answer...

Answer 3

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 4

There is not an adapter harness for your 2007 Lexus GS430. To hardwire this controller to your system you can use the Replacement Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controller 12" Long #20127 to allow you to use the…

view full answer...

Answer 5

Hi Andrei; yep, you're 100 percent right, you should use the 30 amp breaker. That's why for the installation kit I recommend using the Universal Installation Kit for Trailer Brake Controller #ETBC7. The #ETBC7 comes with multiple breakers,…

view full answer...

Answer 6

To duplicate the Universal Installation Kit for Trailer Brake Controller, #ETBC7, minus the 7-way, you will need the Wiring Kit for 2, 4, 6 and 8 Brake Electric Brake Controllers, #5506, Hopkins Trailer Wiring Installation Kit, #HM51010, 40 amp.…

view full answer...

Answer 7

I recommend using at minimum a 12 gauge wire like #12-1-1, but preferably 10 gauge wire like #10-1-1. When you try to run 12v power for electric brakes through a thinner 14 gauge wire to power something like your brakes it overloads the wire and…

view full answer...

Answer 8

You'd want to use the 20 amp circuit breaker like #PK54220PL unless your trailer has more than two brake axles. If that's the case you'd want to use the 30 amp breaker #38630.

view full answer...

Answer 9

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 10

On an 4 foot long section of E-track #EM19147 and 2 screws every 16 inches that is a total of 6 screws in the aluminum frame. This most likely will not get you near the capacity of the E-track. I recommend bolting through the aluminum frame so that…

view full answer...

Answer 11

The Hopkins 6 Pole to 7 Pole Adapter, #47435, does have a pin for the brake output for a brake controller. This adapter will work for your set up as long as the center pin of the 6-way plug on your RV is for 12v power and the pin in the 10 o clock…

view full answer...

Answer 12

You'll need a 20 amp circuit breaker for the brake controller power and a 40 amp circuit breaker for the battery charge line circuit from the trailer connector for a total of two. We actually offer a kit with these circuit breakers as well as the…

view full answer...

Installing A Brake Controller On A 2000 Holiday Rambler Admiral

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching