2006 Holiday Rambler Brake Controller Install Port Location

Question

Question:

Where do you tie the signal wire for the Prodigy 2 controller in on the coach? i read in another post about a wire marked brake sig from control box 3 but that was an older model.i know where to tie in the other wires just need to figure out the sig wire. 2006 Holiday Rambler Imperial w/Air brakes

asked by: Mark D

0

Expert Reply:

The correct harness to use on your 2006 Holiday Rambler that is built on the Ford F-53 Chassis is the part # 3034-P for installing a Tekonsha brake controller. The port to plug in a brake controller is up under the dash behind the instrument cluster. It is not easy to get to but it is there. Ford has a document Q-206 with pictures that should help that is available online. I attached a picture from it that should help as well.

For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup.

expert reply by: Jameson C

0

click to enlarge

Answer 1

On some Holiday Ramblers the wiring port for a trailer brake controller can be found under the left side control panel next to the driver's seat. The four wires should be +12V (black), brake switch signal (red), brake output (blue) and ground…

view full answer...

Answer 2

Yes, one of the few consistencies in trailer-related wiring is that all trailer brake controllers such as the Prodigy P3 #90195 use the same 4 wire colors for specific functions. The controller's Black wire connects to the vehicle battery via a…

view full answer...

Answer 3

The best way to confirm the presence and location of a brake controller installation port in your 2006 Holiday Rambler Ambassador is to provide the coach's VIN to the manufacturer so that they can confirm which model year of base chassis was used…

view full answer...

Answer 4

A brake controller like the Tekonsha P3 will work just fine with the air braking system on your motorhome. The controller will get its input from the brake stoplight switch, which tells it when the brakes are being applied. If there is a 7-way…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Hey William, thank you so much for all of the information! To replace your axles, I recommend the Trailer Axle w/ Electric Brakes item #e73SR. This is a 6,000 lbs axle that come ready to install with pre-greased hubs and electric brake assemblies.…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Hey Frank, thanks for reaching out! What Dexter Axle means by this is that you want the grease zerk fitting from the wet bolts in the Dexter E-Z Flex Suspension Kit #K71-653-00 to face the outside of the trailer, rather than under the trailer. I see…

view full answer...

Answer 11

Thank you for providing that information. Leaf springs like the ones you have now typically match the axle capacity on your trailer. Although adding leaf springs with a slightly higher capacity won't hurt, it also is not necessary. Based on the…

view full answer...

Answer 12

It sounds like you are looking for a u bolt kit for a 3,500 lbs axle. The 3-Leaf Double-Eye Spring for 4,000-lb Trailer Axles - 25-1/4" Long item #e57SR will work great for a tandem axle suspension system. For your ubolt kit you're going to…

view full answer...

2006 Holiday Rambler Brake Controller Install Port Location

Continue Researching