Do Bulldog and Fulton Trailer Jacks Use Same Snap Ring Dimensions

Question

Question:

It has a Bulldog Swing away trailer jack that has a snap ring. Are the snap ring sizes universal or, is there a difference that would prevent interchanging them?

asked by: Tom J

0

Expert Reply:

The Bulldog and Fulton jacks use the same snap ring dimensions like the part # FP908600 which has an inner diameter of 2-5/16 inches.

That means the part # FTJ120W0301 will fit on your trailer's mounting bracket that had a Bulldog jack installed on it.

expert reply by: Jameson C

0

Answer 1

The Fulton Round, Snap-Ring Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,200 lbs #FTJ120W0301 provides similar capacity and does have a Snap ring pilot hole diameter of 2-1/2"that lines up with your Bulldog Jack.

view full answer...

Answer 2

Since Fulton and Bulldog jacks fit the same size snap rings and since Bulldog doesn't offer a similar jack that has a wheel caster your best solution is the Fulton part #FTJ120W0301 which would fit the same snap ring and comes with a wheel…

view full answer...

Answer 3

If you can send a photo of the jack mounting bracket I can confirm this, but you've likely got a retaining ring like the Replacement Retaining Ring for Bulldog and Fulton Snap-Ring Jacks #FP908600. They make snap ring pliers that are used to…

view full answer...

Answer 4

The weld on bracket that is included with the Fulton Swivel Jack #FTJ120W0301 does have an outer diameter of 2 1/2 inches. The bracket that comes welded to the jack is slightly larger to accommodate for the 2 1/2 inch bracket to swivel once…

view full answer...

Answer 5

Jack #DL22210 isn't a snap ring jack but we do have other options that will likely work with your existing mount such as #FTJ120W0301. The hole spacing for the pull pin is 3 inches apart on center. I have linked a video review of this jack for…

view full answer...

Answer 6

The mount style of your jack is not a current style that Bulldog makes so we aren't able to get you a replacement mount so best option would be a new jack like the Fulton part #FTJ120W0301 which is pretty similar as it has a wheel caster, a side…

view full answer...

Answer 7

The Pro Series jack part #PS1400300303 is designed to fit on a 2-1/2 inch diameter pipe and snap ring like you are needing so this would work great.

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Do Bulldog and Fulton Trailer Jacks Use Same Snap Ring Dimensions

Product Page this Question was Asked From

Continue Researching