4 Lug Hub Replacement for Hub Marked BT100

Question

Question:

which spindle work with a bt100 4lug hub

asked by: Hubert

0

Expert Reply:

From previous customers with your hub we have found the BT100 hub to be one that has bearing numbers L44643 for the inner and outer bearings.

So for a hub that will fit and has the right bolt pattern you'd need the part # AKIHUB-440-2-1K.

expert reply by: Jameson C

0

Answer 1

Welcome back Jane. The Taskmaster 4.80R12 Radial Trailer Tire w/ 12" Vesper Silver Mod Wheel item #TA99QR weighs 18 lbs. This wheel tire combo includes an older 4 on 4 lug nut pattern. This is a load range C radial tire with a 990 lbs capacity.…

view full answer...

Answer 2

Hello Mark, thanks for getting in touch. The 145/R12 tires and the 4.80-12 are similar but not exactly the same size. The 4.80-12 tires are 4.9" wide and 20.7" in diameter when fully inflated. The 145/R12 tires are going to be about…

view full answer...

Answer 3

We recommend that you pull the hubs off your trailer to inspect and repack the bearings every 12 months or 12,000 miles. If at this time the bearings still appear in good condition then there is no need to replace them. There isn't a general rule…

view full answer...

Answer 4

The bearing part #L44649 has an inner diameter of 1.063 and is typically used in 3,500 lb axle hubs and the #L44643 has an inner diameter of 1 inch and is typically used on 2,000 lb axle hubs. If you can get me more info on your trailer like axle…

view full answer...

Answer 5

Hi Baer; since the #AKHD-550-35-K came pre-greased there is no need to add additional grease at this time. These come with the right amount of so they're ready to go once installed. However, if you want to add some extra grease it won't hurt…

view full answer...

Answer 6

The Dexter Trailer Axle with Idler Hubs - 4 on 4 Bolt Pattern - 60" Long - 2,000 lbs #20440I-ST-60 is powder coated, but not galvanized. The best we can do to make sure it wears well with all the salt water is to instead use the same Dexter…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

The bearings that go on a 1.06" spindle are item #L44649. These are found in this configuration on 2,000 lbs - 2,700 lbs axles. If you can find it there is typically an axle tag or engraving somewhere on the axle that'll have a serial number…

view full answer...

Answer 9

Yes you can go to the larger wheel and tire size of 5.30-12 that you asked about. For a 4 lug wheel version we have the part #AM30780 which would work great. This has a higher speed rating of 81 mph.

view full answer...

Answer 10

Yes the bearing kit part #DL21792 is the correct kit for your trailer hub BT-100. This comes with two bearings L44643 like we know fit that hub part number.

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

4 Lug Hub Replacement for Hub Marked BT100

Product Page this Question was Asked From

Continue Researching