How to Order Replacement Hardware for Draw Tite Hitch 75270

Question

Question:

I purchased a 2014 Honda odyssey and am moving my 75270 trailer hitch from my 2005 to the newer van. I am looking to use new hardware. Do you sell the hardware kit for this? Draw-tite provide me with the following product #: 75270F. Thanks.

asked by: ANDREW L

0

Expert Reply:

We do sell replacement hardware as part # RHK. With this you would need to enter the part number of the hitch on that product page and we will ship you the correct hardware needed for the hitch.

expert reply by: Jameson C

0

Answer 1

Before we determine that you have the wrong size install bolts you need to make sure that the bolts not fitting isn't due to the weld nuts of your vehicle being dirty/corroded and that is why they won't fit. Typically on vehicles that have…

view full answer...

Answer 2

The Draw-Tite Max-Frame Trailer Hitch Receiver part #75270 that you have now is only a fit for a Honda Odyssey from 1999 - 2017. For a 2019 Honda Odyssey you will want to use the Curt Trailer Hitch Receiver part #C64NR. The Curt Trailer Hitch…

view full answer...

Answer 3

The Draw-Tite Hitch #75270 that you are installing on your 2008 Honda Odyssey uses M12 X 1.25 X 35mm bolts and 1/4“ X 1-1/2“ X 2” spacer blocks and you can get replacement hardware for this at part #RHK. We do not have these parts available…

view full answer...

Answer 4

The best hitch you can equip your 2016 Honda Odyssey with is the Draw-Tite Max-Frame, part #75270. I've linked to a video installation of this hitch on a 2016 Odyssey. It's a Class III hitch with a 2" receiver that has a maximum gross…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 8

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hey Adrian! The higher capacity for the B&W #BW47BR and Curt #C77MJ comes from the construction. The B&W hitch weighs 45 lbs and then the Curt and Trailer Mate #TMT54FR both weigh 32 lbs. The Trailer Mate does sit just a tad higher compared…

view full answer...

How to Order Replacement Hardware for Draw Tite Hitch 75270

Products Featured in This Question

Continue Researching