Availability of Bearing Buddy Grease Seal part # BB60001

Question

Question:

Hi Everyone, Bearing Buddies I need part # BB60001 can you supply it? My axle is 1.00inch thats why I need the smaller I.D. 1.020 TIA,

asked by: Mike C

1

Helpful Expert Reply:

We do carry the grease seal part # BB60001 that you referenced.

It has an inner diameter of 1.375 inch and 1.980 inch.

expert reply by: Jameson C

1

Answer 1

Unfortunately, no we do not carry axe sleeve repair kits, so your options would be to replace the entire axle, the spindle, or you can just use the Spindle Grease Seal Set for L44643 Inner Bearing and 1.980 Bearing Buddy #BB60001. This kit is…

view full answer...

Answer 2

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 3

For a hub like the Dexter #34822BX that has a hub bore diameter of 1.98-inches, you'll want to use stainless steel Bearing Buddy #BB1980A-SS. These will provide the best resistance to corrosion and will allow the boat trailer's wheels to be…

view full answer...

Answer 4

When installing the double-lip grease seals like #BB60001 that are needed when using Bearing Buddy bearing protectors like #BB1980A-SS you want to install the rear grease seals as gently as you can, to avoid any deformation of their shape, and only…

view full answer...

Answer 5

It sounds like you are looking for the correct grease seal for your spindle. If your inner bearing is part #L44643 and the grease seal journal, or mounting location, on the spindle is 1.25 inches, then you have two grease seal options. For a standard…

view full answer...

Answer 6

Hi Min, Switching from 4.80/4.00/8 to 5.70-8 would increase your width by a half inch on each side and would give you an overall diameter of 18". The #AM30153 has 4 on 4 bolt pattern and 2.8" pilot hole with zero offset so as long as…

view full answer...

Answer 7

If you have a 1" straight spindle then it uses L44643 inner and outer bearings therefore the correct Spindle Grease Seal Set for Bearing Buddy is part #BB60001.

view full answer...

Answer 8

It looks like you did your homework Ron, because the Bearing Buddy #BB1980A and the Spindle Grease Seal Set #BB60001 are indeed the proper parts for the #AKIHUB-545-2-1K idler hub assembly. This hub uses the #L44643 inner bearing, so the bearing…

view full answer...

Answer 9

Since you have the grease seal and bearings already it would seem that you are looking for replacement races. You can measure to find the replacements or you can get the numbers off of them. I attached a picture that shows all of the replacement…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Availability of Bearing Buddy Grease Seal part # BB60001

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching