How to Pick Out Powered Landing Gear for 1998 Holiday Rambler
Updated 07/18/2017 | Published 07/17/2017
Products Featured in This Question
Question:
I sent an email a few days ago , enquiring about landing legs for a 1998 Holiday Rambler, Alum a lite 30 footer, It has electric and wench hole . Old landing leg fell out on one side, so it is toast! What do you recommend and heaveier size?
asked by: Rix
Expert Reply:
In order to pick out a direct replacement for the landing gear on your trailer we would need to know the distance between the mounting brackets. Otherwise you could just have the brackets removed from your trailer by a qualified welder and then install the brackets that come with the Reese Tandem Landing Gear Set # RP500708. Either way this landing gear set would work well for you, you just might have to have the brackets of your trailer removed and the new ones welded on.
I attached a picture that shows the dimensions that this landing gear set would fit with.
The jacks would be the correct replacement for Lippert, Venture, and Atwood landing gear, as well as those from a few other manufacturers. The sure way to tell is that if the distance between the mounting brackets (underside of top bracket to top of lower bracket as shown in the diagram) is 17-1/2 inches. If this is the case, the landing gear should fit just fine.
If your frame clamps are instead 20-1/4 inches the Ultra Fab part # UF17-943010 would be a direct replacement.
Continue Researching
- Shop: Ultra-Fab Deluxe Electric Landing Gear Set - Weld On - 38" Lift - 12,000 lbs
- Shop: Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor
- Shop: Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs
- Shop: Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 6,500 lbs
- Video: Checking Out the Ultra-Fab Deluxe Electric Landing Gear Set
- Video: What to Know About the Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor
- Search Results: landing gear motor
- Search Results: landing gear crank
- Search Results: landing gear control
- Search Results: landing gear switch
- Search Results: atwood landing gear switch
- Shop: Stromberg Carlson Manual Landing Gear Set - Weld On - 34-7/8" Lift - 8,000 lbs
- Shop: Replacement Motor with Clutch for Lippert Ground Control 2.0 Electric Leveling System
- Shop: Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 6,500 lbs
- Q&A: Does Ultra Fab Landing Gear kit part # UF17-943010 Have Capacity for Trailer that Weighs 14,730 lbs
- Q&A: Replacement Landing Gear Needed for Part # VMC900R-304103
- Q&A: Will The Ultra-Fab Deluxe Landing Gear Set Fit A 1995 Fleetwood Terry 5th Wheel Trailer
- Q&A: Determining if Ultra-Fab Landing Gear Fits Jayco Toy Hauler
- Q&A: Powered Landing Gear Recommendation for a 6,000 lb Gooseneck Trailer
- Q&A: What Is The Difference Between The Landing Gear Set RVLG-8000 & RVLG-8HDL?
- Q&A: How to Choose Replacement Landing Gear for 5th Wheel Trailer
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Search Results: trailer jack
- Article: How to Measure for Trailer Hitch Drop
- Shop: Suspension Enhancement
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
on Camper Jacks
