Is it Possible to Raise Suspension of Trailer that Has Slipper Springs
Updated 07/12/2017 | Published 07/11/2017
Question:
I was looking into the over under kit but it clearly states for closed eye leaf springs only. If my popup has slipper type spring what is my option to raise ground clearance? I have 1997 Coleman popup with electronic brakes
asked by: Dane M
Helpful Expert Reply:
Dexter Trailer Springs Over-Under Conversion Kit, part # K71-384-00, is specified by Dexter for use only with double-eye springs. It is not suitable for use with slipper springs. It is considered by our technical friends at Dexter to be unsafe to use a conversion kit on a slipper spring since one end of it is simply suspended, rather than bolted to a hanger or shackle strap.
One option to consider is to replace the spring hangers on your trailer with longer ones. This will have the effect of lifting your trailer frame relative to the axle. This will also raise the center of gravity of the trailer and alter its handling to some degree. I have provided a link to our main product page for hangers for slipper spring suspensions.
Product Page this Question was Asked From
Dexter Trailer Springs Over-Under Conversion Kit
- Trailer Suspension Parts
- Alignment and Lift Kits
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Double Eye Springs
- Round Axle - 2-3/8 Inch
- Single Axle
- Dexter
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Suspension Enhancement
- Shop: Air Lift 1000 Air Helper Springs for Coil Springs - Rear
- Q&A: How to Raise Suspension of Trailer that Has Slipper Springs
- Q&A: Way to Lift Trailer that Already Has Axles Under Leaf Springs
- Q&A: Solution for Over-Under Conversion Kit on Lowes 4 x 6 Carry-On Trailer
- Q&A: Raising the Height of a Carry On Utility Trailer with 1-3/4 Inch 2,000 Pound Axle
- Shop: Triangular Equalizer for 1-3/4" Double-Eye Springs - 6" Long - 9/16" Center Hole
- Shop: Dexter Single Axle Standard Duty Suspension Kit - Double Eye Springs
- Shop: CE Smith U-Bolt Kit for Mounting 2" Square Trailer Axles - 4-1/2" Long U-Bolts - Zinc
- Shop: Front/Center/Rear Hanger for Double-Eye Springs - 4-1/4" Tall - 9/16" Bolt Hole
- Shop: Curved Equalizer for 1-3/4" Wide Double-Eye Springs - 7-3/4" Long - 9/16" Center Hole
- Shop: Spring Seat for Typical 3,500-lb Round Trailer Axles - Weld-On - Plain Steel
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Hitch
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Q&A: Should I Get Loadlifter 5000 Or 7500 For Towing A 15K Fifth Wheel
- Search Results: trailer wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Search Results: trailer jack
- Article: How to Measure for Trailer Hitch Drop
- Q&A: How to Replace a Lance 6-Pin Plug w/ a Standard 7-Way Connector
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Search Results: trailer tires and wheels
- Shop: Brake Controller
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Search Results: suspension enhancement
- Video: An In-Depth Look at the Roadmaster Battery Charge Line Kit for Towed Vehicles
- Shop: Gooseneck Hitch
on Trailer Suspension Parts
