Recommended Dual Motor Landing Gear for 2007 Weekend Warrior Toy Hauler

Question

Question:

Hello, I own a 2007 Weekend Warrior 3505LE toyhauler and would like to get a dual motor landing gear system. What model will work for my application?? Thanks

asked by: Richard H

1

Helpful Expert Reply:

For your 2007 Weekend Warrior 3505LE Toy Hauler, I recommend looking at the Ultra-Fab Deluxe Electric Landing Gear Set # UF17-943010. These dual 12-volt motors will function independently of one another for simple and effective leveling. It has a lift of 38 inches and a combined weight capacity of 12,000 pounds.

When it comes to trailer jacks or landing gear, I recommend always going with a product like this one that has more lifting capacity than what is actually needed. This will result in a longer lifespan as a result of not being operated near its limit and not working as hard to do their lifting.

I have attached the installation details on this product as well as a short demonstration video for you to check out.

expert reply by: Chris R

1

Answer 1

We can get you un-stranded! The correct follow leg for your landing gear is going to depend on how long it is. If your leg measures 29-1/2" (see attached photo), you would need replacement #LG-179014, which can be used with most landing gear…

view full answer...

Answer 2

One possible cause of the landing gear not working properly is electrical especially considering you have already replaced mechanical parts. If the battery does not have enough charge it can cause the landing gear to not operate properly. But if you…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Recommended Dual Motor Landing Gear for 2007 Weekend Warrior Toy Hauler

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching