Locating Brake Controller Port on 2000 Ford F-150 To Install Hopkins Brake Controller # HM47294

Question

Question:

I do not see the male plug that is said to be attached to my truck.

asked by: John

0

Expert Reply:

The factory brake controller plug should be located under the dash to the right of the steering column. It should be located towards the center of the dash and may be tucked up and out of the way behind some wiring. I have linked an FAQ Article that shows the location of the plug.

You will need the Ford Adapter, part # HM47715, to plug into the brake controller harness and the Ford plug under the dash.

If you have a factory 7-Way on your 2000 Ford F-150, installation is complete after mounting the Hopkins brake controller and plugging the Ford Adapter # HM47715.

If you have a factory 4-Way or no trailer connector on your 2000 Ford F-150, you will also need to install Ford Replacement OEM Tow Package Wiring Harness, part # 118242. In addition, you will need Mounting Bracket for Pollak 7-Pole, part # PK12711U, if you do not have a factory 7-Way.

I have linked instructions for the Hopkins Agility Brake Controller, part # HM47294. Also linked is a video installation of a brake controller using part # 118242 on a 2001 Ford F-150. You will also find an FAQ Article on installing brake controllers on Ford Trucks, which shows where the brake controller plug is located.

expert reply by: Reno H

0

Answer 1

The correct brake controller wiring adapter will depend on which brand brake controller you have. I have a list below with all the harnesses that will plug directly into the port under the dash of your 2003 Ford F-250 and their specific brand brake…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Locating Brake Controller Port on 2000 Ford F-150 To Install Hopkins Brake Controller # HM47294

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching