Does Equalizer Weight Distribution Head Fit Blue Ox Weight Distribution Shank

Question

Question:

Blue Ox SwayPro Weight Distribution Shank for 2inch will the head off an equalizer weight distribution hitch fit that

0

Expert Reply:

Yes, the weight distribution manufacturers thankfully designed the shanks to their systems to all be the same dimensions. That means a Blue Ox shank like part # BXW4002 will fit an Equalizer weight distribution head.

expert reply by: Jameson C

0

Answer 1

Swapping out the shank of your Equal-i-zer WDH with a larger 18" shank would push the trailer back an additional 6" for more clearance but there's no way for me to confirm that your trailer would completely clear the tail lights on your…

view full answer...

Answer 2

The Blue Ox SwayPro Weight Distribution Shank for 2-1/2" Hitch #BXW4028 weighs 25-lbs. Your current shank, the Blue Ox TrackPro Weight Distribution Shank for 2" Hitches #BLU28FR weighs 20-lbs so the change between the tow really won't…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 12

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Does Equalizer Weight Distribution Head Fit Blue Ox Weight Distribution Shank

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching