Difference Between Atwood Protechtor and Non-Digital Carbon Monoxide and LP Gas Detector

Question

Question:

what is the difference between this and the 2001 series or should i order the 2001 wich is what is in my travel trailer now. i have a 2011 passpot by keystone .

asked by: Jesse C

1

Helpful Expert Reply:

The Atwood 2001 Protechtor you have is for detecting just propane whereas the part # AT36681 detects propane and carbon monoxide.

expert reply by: Jameson C

1

click to enlarge

Answer 1

To replace the Extend/Retract Switch for Lippert Electric Trailer Jack #LC49MD you'll just need to keep track of how the original was hooked up and replicate that. Unfortunately Lippert doesn't have a wiring diagram but we do have a photo we…

view full answer...

Answer 2

Hi Matt, There is; the MORryde you have is essentially the replacement for the Lippert Rhino, so you'd want the Gen-Y that replaces the Rhino. The 5,500 lb pin weight Gen-Y that fits in place of the Rhino is the following: - Gen-Y Hitch Shock…

view full answer...

Answer 3

Hey Tim! For a boxed cargo trailer with the body sitting over most of an A-Frame tongue then you'll want to use the Adco SFS AquaShed Trailer Cover #290-46004 because it's tailored for that style of trailer. If you have a different style…

view full answer...

Answer 4

I wasn't able to find the Atwood 36720 RV Propane Gas Detector you mention, however I was still able to find the RV Propane Gas Detector #RS64FR in white, or #RS44FR in black to work as a replacement for your Protechtor Series 2001 LP Gas…

view full answer...

Answer 5

The Atwood RV Carbon Monoxide and Propane Gas Detector part #AT36681 has three wires as you mentioned but only two will need to be used. There are two red wires and one black wire. The black wire is ground and the two red wires are for power. Only…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Hey Tim, I checked out your Predator 5000 generator and it does use a quick connect propane connector like what the part #CAM57629 provides so yes this would work. How do you like the Predator generator?

view full answer...

Answer 9

The brake wire providing voltage is wired in parallel, with one lead from each magnet being grounded to the trailer frame. We have a great Wiring Help Page that shows a diagram, I will provide a link to it below.

view full answer...

Answer 10

We do have an option for replacing your Elixir ELX-60. Unfortunately there is not going to be a direct replacement for the converter section. You will need to replace the entire panel with the Progressive Dynamics 4500 Series RV Converter…

view full answer...

Answer 11

Even on manufactured trailers wiring colors can vary so there is no way to say for sure. The only way to know which wire is tied to which function is to trace the wire back. On an SAE standard 7-way the brown wire would be the tail/running lights. On…

view full answer...

Answer 12

The biggest difference will be capacity. The Curt Hitch part #C15302 that you referenced is on the high end of the capacity spectrum. It's a Class V hitch that has the following capacities: Maximum gross trailer weight: 16,000 lbs Maximum GTW…

view full answer...

Difference Between Atwood Protechtor and Non-Digital Carbon Monoxide and LP Gas Detector

Continue Researching