Where Does Scissor Step AS23 Install Typically at Rear of Camper

Question

Question:

I am looking for folding steps for my 88 Lance camper that rides on a Ford F 350 Dually crew cab long bed. The camper is an 8 ft so ends at the back of the truck bed and does not hang over. The bumper, license plate, hitch are all there and I am trying to visualize where a scissor step would fit......

asked by: Carol

0

Expert Reply:

If you check out the install picture I attached for the # AS23 you can see where it normally installs at the rear of a camper that is installed on a truck. Without seeing your setup it's hard to be more specific but there should be a spot on the camper below the door that allows the mounting bracket to install.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Brophy Camper Scissor Steps for truck campers, #AS04, are intended for an entry height of 31" to 40". If your camper door sets within that 31-40' range then yes this will fit your rig. Please see attached image for measuring points…

view full answer...

Answer 2

There are steps that can work for your Northwind camper and I recommend checking out the Brophy Camper Scissor Steps #SS03 which is a triple step that will work with your 24" height. These are not permanently mounted; instead you install a…

view full answer...

Answer 3

The Brophy Camper Scissor Steps part #SS03 weigh 27 lbs total.

view full answer...

Answer 4

The HSSF hold down brackets would use the Tie Down Hardware Package, part #TDHP, which includes hooks, chain and turnbuckles. The tie down hardware would typically attach to existing eye bolts built into the underside of camper. If your camper does…

view full answer...

Answer 5

That is correct, you can tap into the plug and it will provide a charge but keep in mind that this is not the most efficient way for charging a battery. This method does not provide any charge balancing or battery charge management and on newer…

view full answer...

Answer 6

The Aluminum Scissor Steps #AS03 that you referenced weigh 15 lbs and the Scissor Steps #SS03 weigh 29 lbs. As you can see, aluminum is much lighter.

view full answer...

Answer 7

The Brophy Clamp On Camper Tie-Downs #HSSF will have a very slight amount of play since there is a compressible pad to prevent scratches on the bedrails, but it sounds like you're having much more significant play. I've attached a picture…

view full answer...

Answer 8

For your 2005 Dodge Ram 1500 and the Brophy camper tie downs #TDSF you will need hardware that is the right grade and for the right material (in this case steel) just longer than the included hardware. I recommend using grade 8 hardware. A hardware…

view full answer...

Answer 9

Any time I am having problems removing difficult suspension components I usually apply liberal amounts of lubricant, such as LubriMagic Green Series Biobased Spray Lubricant, let it soak in for a minute and then try again. If possible try using a…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Where Does Scissor Step AS23 Install Typically at Rear of Camper

Product Page this Question was Asked From

Continue Researching