Do I Need to Uninstall the Wiring to Use the 6 and 7-Way Trailer Connector Mounting Box, 2-1/2

Question

Question:

Do you have to unwire and then rewire an existing female connector socket to install it in this mounting box? My socket was never attached to my motorhome, just left hanging from a zip tie from the frame.

asked by: JP H

1

Helpful Expert Reply:

No, you will not have to uninstall and then reinstall the wiring on your current 6-Way or 7-Way wiring harness to use the Trailer Connector Mounting Box part # 18159.

expert reply by: Jon G

1

click to enlarge

Answer 1

I have the perfect solution for you, but since the crosstube on the Draw-Tite hitch #76227 is completely concealed behind the bumper of your 2019 Subaru Outback Wagon, a traditional mounting bracket that clamps onto it, won't work. Instead, take…

view full answer...

Answer 2

Here's what I'd recommend. If you have an exposed portion of the hitch crossbar to work with, use the #18136 no drill bracket. This fastens to the hitch crossbar using an included pipe clamp. You'll also use the #PK12711U 7-way mounting…

view full answer...

Answer 3

To tow a trailer with brakes and install a 7-Way harness on your 2024 Honda Odyssey you will need two separate wiring harnesses because they don't make just one that'll do the job. The first harness you'll need is the Curt T-Connector…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Do I Need to Uninstall the Wiring to Use the 6 and 7-Way Trailer Connector Mounting Box, 2-1/2

Featured Help Information

Miscellaneous Media

Continue Researching