Looking For 2-5/16 Inch Hitch Ball With Shank Diameter Of 1-1/2 Inches

Question

Question:

Hi, Im looking for a 2 5/16inch ball with a shank diameter of 1 1/2. Its a regular screw in. I cant find that shank diameter on your site. Do you carry them? Thank you

asked by: Greig R

0

Expert Reply:

We do have 3 options of hitch balls in that shank diameter of 1-1/2 inches. Each has a 30,000 lb capacity rating and they have different rise amounts from the base of your ball mount to the top of the ball. Here are your options:

B&W 2-5/16" Hitch Ball w/ 2" Rise - 1-1/2" Diameter x 2-3/4" Long Shank - Raw - 30K # BWHB94006
B&W 2-5/16" Hitch Ball w/ 1" Rise - 1-1/2" Diameter x 2-3/4" Long Shank - Raw - 30K # BWHB94005

expert reply by: Jason S

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 5

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 10

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 11

You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller #C24VV. The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like under…

view full answer...

Answer 12

No, it will not Bryan. The Redarc Tow-Pro Link item #RED57AR requires a USCAR port that comes with factory tow packages. The Stealth Hitches Hidden Trailer Hitch Receiver w/ Towing Kit item #SH25VR, that fits your 2023 BMW X5, does not have this…

view full answer...

Looking For 2-5/16 Inch Hitch Ball With Shank Diameter Of 1-1/2 Inches

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching