Parts Needed to Add 7-Way Wiring & Brake Controller to 2000 Jeep Wrangler

Question

Question:

I have a 2000 Jeep Wrangler TJ, I want to pull a trailer with a 7-contact blade round connector. What parts do I need?

asked by: Bob S

0

Expert Reply:

A trailer that has a 7-way type wiring setup probably has electric drum brakes. To tow such a trailer with your Wrangler you will need a brake controller like the reliable Prodigy P2 # 90885 along with the 7-way wiring setup.

You'll first need to have a 4-pole harness on the Jeep; if you do not already have one you can use part # 118409 which offers simple plug-in installation at your taillights. Then you will convert that wiring to the 7-way type by using our kit # ETBC7. This kit includes the 7-way socket and all the components you need to install the brake controller. No other items are needed.

The linked video shows you the entire installation process for the # ETBC7 kit and the brake controller.

expert reply by: Adam R

0

Answer 1

The wires to install the Prodigy P3 #90195 are indeed already run and under your dash. I have added a link to an installation video showing exactly how to install this brake controller in a 2011 GMC Sierra like yours. On the Prodigy the blue wire is…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Parts Needed to Add 7-Way Wiring & Brake Controller to 2000 Jeep Wrangler

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching