2017 Jeep Wrangler Rubicon Front Hitch Fit Recommendation

Question

Question:

Can you tell me if this hitch would fit on a 2017 jeep Wrangler Unlimited Rubicon ? And if not what is stopping the installation?

asked by: Jeff

0

Expert Reply:

Curt part # 31432 and Draw-Tite part # 65069 are both front-mounted 2-inch hitches intended for the 2017 Jeep Wrangler Unlimited with standard factory front bumper. But if you have a special Rubicon edition you will want the Curt # 31432.

expert reply by: Jameson C

0

Answer 1

From my research I found the FHK31432 plow you mentioned requires a front hitch with a 2 inch receiver opening and a minimum tongue capacity of 300 lbs and minimum tow capacity of 3,000 lbs. We have just what you are looking for. The trim package on…

view full answer...

Answer 2

The installation instructions for Curt front hitch #31432 do not include an actual full-size template for trimming the underbody deflector panel but they do include a helpful diagram that shows where to trim it. Please note this is only required if…

view full answer...

Answer 3

For your 2015 Jeep Wrangler the front hitch I would recommend is the Draw Tite part #65069 as it has the highest capacities and the lowest price.

view full answer...

Answer 4

After comparing the two front hitches we have available for the 2016 Jeep Wrangler Unlimited, I agree with you and recommend the Draw-Tite Front Mount Trailer Hitch Receiver #65069 over the Curt Front Mount Trailer Hitch Receiver #31432. The…

view full answer...

Answer 5

You are correct that both the Curt #C94WR and Draw-Tite #DT22MR you were looking at for your 2022 Hyundai Tuscon are very similar. Both hitches share the same 525lb tongue weight and 3,500lb trailer weight ratings, both share the same hidden…

view full answer...

Answer 6

Since both hitches are rated for higher than the capacity of your 2024 Jeep Grand Cherokee the capacity really isn't as important of a factor. The smaller factors like the length of the receiver tube and how the safety chain loops sit would be…

view full answer...

Answer 7

The Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2" #65069 has the outside edge to outside edge measurement of 26-1/8 inches and the hole center to hole center measurement of 17-7/8 inches. I've attached a photo to assist.

view full answer...

Answer 8

The front mount trailer hitches for a 2016 Jeep Wrangler Unlimited like the Draw-Tite Front Mount Trailer Hitch Receiver part #65069 are all designed for models with the factory front bumper. It is no possible for the manufacturer nor I to confirm…

view full answer...

Answer 9

There is only one way to tell if they can be used together. Check the mounting location of your front hitch where it attaches to the frame of your jeep. I was unable to find your purchase of the Draw-Tite hitch in our system but the Draw-Tite Hitch…

view full answer...

Answer 10

The Draw-Tite Front Mount Trailer Hitch Receiver, part #65069 is a good fit for your 2008 Jeep Wrangler. I have attached a drawing that shows how the hitch is attached to the vehicle. As you can see, the attach points are on the underside of the…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

2017 Jeep Wrangler Rubicon Front Hitch Fit Recommendation

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching