Availability of Trailer Fender that Measures 32x10x15

Question

Question:

My trailer uses bolt on fenders 32x10x15 Do you have fenders to bolt on in this size

asked by: Robert J

0

Expert Reply:

The closest fender we have dimensionally to what you listed is the part # CE17100ATB which is a diamond plate fender that measures 32" Long x 10" wide x 16" tall. Typically this fender uses the mounting brackets part # CE26098G-2 which bolt to the fender and the trailer.

expert reply by: Jameson C

0

Answer 1

Yes, these 16-Gauge Steel, Single-Axle Trailer Fender, part #HP79VR, should bolt up to your Barron 5x8 trailer after you drill a few holes it it. This fender is for wheels that are 13-14 inches like what is on your trailer. The dimensions of this…

view full answer...

Answer 2

To replace the fender on your 2022 Arising Ind. cargo trailer I recommend the following: - CE Smith Single Axle Trailer Fender #CE17100ATB To install this on your trailer you'll need mounting brackets light part #CE26098G-2 as well as mounting…

view full answer...

Answer 3

Hey Paul, having the hitch ball height right around 20 inches or so would work fine. It doesn't have to be super exact but if you can shoot for same dimensions when the trailer is level and truck is unloaded you'll be fine. So 19.5 to 20…

view full answer...

Answer 4

If you can send me a photo of the trailer jack I would be more than happy to help you find a replacement, but unless the jack is still under warranty we won't be able to swap it outright with what came on your trailer when you purchased it.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Availability of Trailer Fender that Measures 32x10x15

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching